Discovery Opens up New Possibilities for Solar Energy Conversion and Supercapacitors
February 13, 2017 | University of ManchesterEstimated reading time: 1 minute
Scientists at The University of Manchester have ‘re-discovered’ a material, which could make the construction of 2D van der Waals heterostructures easier to build. Graphene was the world’s first two-dimensional material isolated in 2004 at The University of Manchester, it is 200 times stronger than steel, lightweight, flexible and more conductive than copper.
Since then a whole family of other 2D materials have been discovered and continues to grow. Using graphene and other 2D materials, scientists can layer these materials, similar to stacking bricks of Lego in a precisely chosen sequence known as van der Waals heterostructures to create high-performance structures tailored to a specific purpose.
One of the challenges when creating these heterostuctures is the painstaking stacking of the individual components on top of each other.
However, as reported in Nature Communications, a team supervised by Professor Robert Dryfe have discovered that franckeite (a mixed-metal sulphide mineral first discovered in 1893) naturally stacks into 2D sheets.
This results in van der Waals heterostructures, which can be exfoliated down to a single layer using simple scotch-tape mechanical exfoliation- the method used to isolate graphene. Importantly, this behaviour is likely to be common in a wider family of materials and could be exploited as an alternative to artificial stacking of two-dimensional materials.
Franckeite also opens us new possibilities for energy storage applications such as solar energy and supercapacitors due to its excellent electrical conductivity and remarkable electrochemical properties.
Research Associate Matěj Velický who led the experimental work said “We believe that this work will be followed by further studies of other natural van der Waals heterostructures and that the results will accelerate progress in the emerging “bottom-up” chemical synthesis of such complex structures”.
Prof Robert Dryfe said, “This work is a perfect demonstration of the continual surprises that are revealed through the study of 2D materials”.
Suggested Items
DuPont Showcases AI Innovations Featuring Advanced Interconnects at 2024 International Electronic Circuits Exhibition
05/13/2024 | DuPontDuPont announced it will showcase its comprehensive range of advanced circuit materials and solutions at the 2024 International Electronic Circuits Exhibition in Shanghai. With a product portfolio that includes fine line, signal integrity, power and thermal management, DuPont will exhibit at Booth #8L06 at the National Exhibition and Convention Center (NECC) from May 13 to 15.
MKS’ Atotech to Participate in ECTC
05/10/2024 | MKS’ AtotechAt this year’s 74th IEEE Electronic Components and Technology Conference (ECTC), MKS’ Atotech will present and demonstrate its latest product and service innovations.
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.