Skoltech-led Team Sheds Light on How CNT Could Pave Way for Next-Gen Electronics
November 22, 2017 | SkoltechEstimated reading time: 2 minutes
A team of Skoltech scientists, in collaboration with researchers from the IBM Watson Research Center, have shed light on the behavior of electrical contacts in carbon semiconductor nanotubes – a revelation that could pave the way to next-generation electronics.
Carbon is extremely tough and relatively light with unique electronic and optical properties. Since their discovery some 20 years ago, scientists have been actively investigating their myriad potential uses, as well as their unique properties. As an example, carbon nanotubes are known to conduct electricity significantly more efficiently than other materials, such as silicon and copper.
Silicon digital electronics have revolutionized our experience of the world. Silicon microprocessors are found in technologies ranging from mobile phones to jumbo jets. In the past, tech devices were made possible by a reduction in transistor size, but the possibilities of silicon have effectively reached their limit; thus, it is necessary to search for new opportunities to reduce costs and increase performance in electronic devices.
Toward this end, technology giants like IBM are actively investigating their potential to replace silicon in next-generation computers and other electronics. The primary challenge in this regard is contact resistance, which is attributable to the low resistance of nanotube channels.
“Transistor resistance includes both channel and contact resistance. The channel resistance of carbon nanotubes is better than that of silicon, but no one needs transistors made of nanotubes with a long channel, and when the tube size decreases to several tenths of a nanometer, the contact resistance begins to dominate,” said Skoltech Professor Vasili Perebeinos, the study’s lead author.
Semiconductor tubes are used to manufacture transistors. But metal is used for contacts. Metal exerts pressure on the tubes, which comes at the expense of surface tension. Previous research in the field revealed that this pressure is high enough to flatten the tubes.
“In our latest research, we, quite unexpectedly, predicted that semiconductor tubes flattened by a metal contact become metallic. In this case, the contact resistance increases, and does not subsequently decrease. This is due to the breaking of the axial symmetry of the deformed tubes under the metal contact,” Perebeinos said.
The Skoltech-led team’s research has helped elucidate the steps that can be taken to reduce contact resistance. They determined that for purposes of manufacturing transistors, it’s preferable to use tubes with relatively small diameters.
To put this into context, we can imagine a comparable situation in the macro world. Imagine a large pipe instead of a nanotube, and a hammer pounding against the pipe instead of metal exerting pressure. It immediately becomes clear why a diametric reduction would help; it would be easier to flatten a pipe with a large diameter than one with a smaller diameter.
It is also possible to use metals with a lower surface tension; the “hammer blow” in this case would be weaker and the nanotube would not be flatten.
Suggested Items
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.