Quantum Dot Lighting Takes Forward Leap Thanks to Superacid Treatment
March 15, 2018 | Oregon State UniversityEstimated reading time: 2 minutes
A “superacid” much stronger than automobile battery acid has enabled a key advance toward a new generation of LED lighting that’s safer, less expensive and more user friendly.
Researchers at Oregon State University used the organic superacid to improve the performance of “quantum dots” made from copper indium disulfide, a compound much less toxic than the lead or cadmium that typically serve as the basis for the light-emitting nanocrystals.
Used in optics and electronics, quantum dots have been around for some time. But they can be expensive to manufacture as well as unsafe for some potential applications, including biomedical imaging, because of lead and cadmium’s toxicity.
“There are a variety of products and technologies that quantum dots can be applied to, but for mass consumer use, possibly the most important is improved LED lighting,” said Greg Herman, professor of chemical engineering in the OSU College of Engineering. “And there are now light-emitting nanocrystal TVs on the market that use quantum dots.”
Manufacturing techniques being developed at Oregon State are dealing with the toxicity issue and should scale up to large volumes for low-cost commercial applications. They also will provide new ways to offer the precision needed for better color control; the size and composition of the particle is what determines the color of the light.
In this latest study, published in Materials Letters, researchers created a superacid treatment that improves the photoluminescence of the non-toxic, non-heavy metal quantum dots to the point of being comparable with the best-performing quantum dot material, cadmium selenide.
“The light emission from the superacid-treated dots is much better,” said Herman, the study’s corresponding author. “There are still issues that need to be addressed, but what we’ve shown with this is the ability to improve the lifetime of the quantum dots, and much higher quantum efficiencies. And because these quantum dots are non-toxic, the potential exists for biomedical applications as well.”
A cancer patient, for example, could ingest highly stable dots that would collect at tumor sites to allow imaging.
“That’s another reason we’re working with copper and indium,” he said. “You don’t want people to ingest cadmium or lead.”
The National Science Foundation and Sharp Laboratories of America supported this research. Collaborators included then-OSU graduate students Yagenetfere Alemu and Gustavo Albuquerque.
Earlier quantum dot advances at Oregon State involved the development of a “continuous flow” chemical reactor, as well as microwave heating technology that’s conceptually similar to the ovens owned by most U.S. households.
The continuous flow system is fast and energy efficient and will cut manufacturing costs. And the microwave technology allows for precise control of the heat needed during the manufacturing process, translating into nanoparticles that are the size, shape and composition they need to be.
About the OSU College of Engineering
The OSU College of Engineering is among the nation's largest and most productive engineering programs. Since 1999, the college has more than tripled its research expenditures to $37.2 million by emphasizing highly collaborative research that solves global problems. It is a leader in signature research areas, including precision health, clean energy, resilient infrastructure and advanced manufacturing; and targeted strategic areas, including robotics, materials research and clean water.
Suggested Items
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.