Molecularly Thin Hybrid Perovskite for Advanced Optoelectronic Applications
December 7, 2018 | NUSEstimated reading time: 2 minutes
NUS scientists have discovered that the light emission properties of molecularly thin two-dimensional (2-D) hybrid perovskite can be tuned in a highly reversible way for ultrathin optoelectronic applications. A highly efficient photodetector has been fabricated using hybrid perovskites with the thickness of a single quantum well.
Layered perovskites are solution processible, low-cost materials that can be used as photo detectors or light emitters. The superior ability of the perovskite crystal to detect and emit light with high efficiency is expected to find practical applications in various fields. Each basic unit of a 2D hybrid perovskite is constructed using a semiconducting layer of inorganic material sandwiched between two organic insulating layers. While researchers have studied layered perovskites in their bulk form for the past thirty years, the properties of these crystals when their thickness is thinned down to a few and single layers have largely not been explored.
A research team led by Prof Loh Kian Ping, from the Department of Chemistry, NUS has discovered that a molecularly thin layer of perovskite can be strained in a highly reversible manner without introducing permanent defects on the material that can affect its light emission properties. Also, the emission properties of the perovskite can be tuned reversibly under repeated strains. The researchers achieved this by encapsulating the surface of the perovskite with a thin layer of optically transparent hexagonal boron nitride. This barrier layer traps the organic molecules on the surface of the perovskite layer, preventing them from escaping into the air even under strong laser irradiation.
Using a temperature controlled crystallisation method, the researchers synthesised centimetre-sized perovskite single crystals of the Ruddlesden-Popper phase (a form of layered perovskite structure). These specially prepared crystals are much larger than the usual micron-sized ones and allowed the team to peel off thin layers from it using the “scotch tape” method (similar method used for obtaining graphene from graphite). These ultrathin crystals were then used for the experiments.
Prof Loh said, “Unlike bulk perovskites where the organic chains of adjacent layers are interdigitated and tightly-packed, the layer of organic chain on ultrathin perovskites can “relax” more easily under laser or thermal activation. This “relaxation” process changes their light emission properties. We found that the light emission can reverse back to its initial state by constraining (“de-relaxing”) the surface of the ultrathin perovskite layer.”
We have also studied the atomic structure of these perovskites using the QPlus atomic force microscope. Depending on the supplied thermal energy, the organic layers on the surface can assemble and change the optoelectronic properties of the crystal in a reversible manner. This could potential be used for developing strain-tuneable optoelectronic devices,” added Prof Loh.
Figure 1: (a - e) Optical image of large sized 2D hybrid perovskites (single crystal) and different homologous series (compounds with the same functional group but differ by the number of repeating units) from n = 1 to n = 4. (f - j) Schematics showing the structure of the unit cell. (k - o) Atomic force microscopy images and profile of the exfoliated single unit cell perovskite layers.
Figure 2: An artist’s impression of laser interaction with a molecularly thin 2D perovskites encapsulated by hexagonal boron nitride (blue layer).
Suggested Items
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Happy’s Tech Talk #27: Integrated Mesh Power System (IMPS) for PCBs
04/08/2024 | Happy Holden -- Column: Happy’s Tech TalkA significant decrease in HDI substrate production cost can be achieved by reducing the number of substrate layers from conventional through-hole multilayers and microvia multilayers of eight, 10, 12, and more to only two layers. Besides reducing direct processing steps, the yield will increase as defect-producing operations are eliminated. The integrated mesh power system (IMPS) was invented in the latter years of MCM-D use for thin-film fabrication. Those geometries fit today into our use of ultra HDI.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
Now Available: Episode 4, Season 2 of Designing for Reality—Lamination
04/04/2024 | I-Connect007I-Connect007 has just released the latest episode of its podcast series, On the Line With..., which focuses on designing for reality in the electronics industry. Multilayer boards bring along a completely different set of processes. In this installment, ASC Sunstone VP/Manager Matt Stevenson discusses manufacturing techniques for multilayer boards. Of course, this necessitates a review of drill and registration techniques, followed by the ins and outs of lamination.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.