Standard of Excellence: Speed vs. Quality in Customer Service
Knocking Down the Bone Pile: Revamp Your Components with BGA Reballing
Global Sourcing Spotlight: Balancing Speed and Flexibility Without Sacrificing Control
A Robot's Place in SMT
October 15, 2014 | Scott Zerkle, Yamaha Motor IM America Inc.Estimated reading time: 1 minute
Issues in the SMT Process
The SMT industry’s one constant is change. Standards are continually updated and components are miniaturized for space savings. In addition to the changes that come, the industry is also faced with continuing to deal with areas that fail to change and update. A typical PCB manufacturer lays out a line based on the need to put solder paste on a PCB, place parts in the paste, and then reflow the product (Figure 1). The board size, typical components placed, and the required speed for the line are then considered.
Eventually, a SMT manufacturing line is purchased that can handle a large majority of the process needs. In almost all cases, there will be a component that cannot be handled by the automated process currently in use on the factory floor. This problem is not caused by the engineer who specified the line, nor is it the chosen vendor’s false advertising. This problem plagues virtually all PCB manufacturers because it is not cost-effective to purchase a specialty machine to handle a component that is expected to go away and not be used any more, or the component that is through-hole and was expected to be replaced by a SMT component soon.
Manufacturers are expected to build as demanded and very often that demand is outside of the specifications which they thought were adequate, but the quantity does not justify new special equipment. PCB manufacturers, for example, face the challenge of placing very large connectors, whose size is outside the specifications of SMT machines (Figure 2). Some manufacturers use through-hole components in products (Figure 3), though not enough need exists to justify purchasing a through-hole machine.
Infrequently used components may fail to justify standard packaging for use, and oddly shaped parts may simply be beyond the scope of what a standard SMT machine can handle. In addition to the difficulty in managing the changes in size and type of component for placement, manufacturers must also consider the cost-effectiveness of any solution they devise for managing these “out-of-spec” placement issues. Rarely do these issues justify the expense of purchasing a specialty machine. Rather, the manufacturer finds it more cost effective and more realistic to manage these processes with human resources.
Read the full article here.
Editor's Note: This article originally appeared in the September 2014 issue of SMT Magazine.
Share on:
Testimonial
"In a year when every marketing dollar mattered, I chose to keep I-Connect007 in our 2025 plan. Their commitment to high-quality, insightful content aligns with Koh Young’s values and helps readers navigate a changing industry. "
Brent Fischthal - Koh YoungSuggested Items
Designers Notebook: Power and Ground Distribution Basics
10/29/2025 | Vern Solberg -- Column: Designer's NotebookThe principal objectives to be established during the planning stage are to define the interrelationship between all component elements and confirm that there is sufficient surface area for placement, the space needed to ensure efficient circuit interconnect, and to accommodate adequate power and ground distribution.
PCBA Market Poised to Reach $147.5 Billion by 2035
10/20/2025 | Globe NewswireGlobal printed circuit board assembly market is projected to reach $147.5 billion by 2035, at a CAGR of 4.7% during the forecast period 2025-2035
Würth Elektronik Participates in EU Initiative PROACTIF for Cutting-edge Drone and Robotics Solutions
10/14/2025 | Wurth ElektronikWürth Elektronik is a partner in the visionary EU project PROACTIF, funded under the Chips Joint Undertaking (Chips JU). The international consortium of 42 partners from 13 countries aims to strengthen Europe’s technological sovereignty i
Knocking Down the Bone Pile: Revamp Your Components with BGA Reballing
10/14/2025 | Nash Bell -- Column: Knocking Down the Bone PileBall grid array (BGA) components evolved from pin grid array (PGA) devices, carrying over many of the same electrical benefits while introducing a more compact and efficient interconnect format. Instead of discrete leads, BGAs rely on solder balls on the underside of the package to connect to the PCB. In some advanced designs, solder balls are on both the PCB and the BGA package. In stacked configurations, such as package-on-package (PoP), these solder balls also interconnect multiple packages, enabling higher functionality in a smaller footprint.
Sumitomo Riko Boosts Automotive Design Efficiency 10x with Ansys AI Simulation Technology
10/13/2025 | SynopsysSumitomo Riko is implementing Ansys, part of Synopsys, Inc. AI technology to accelerate time-to-solution and improve efficiency during the design and manufacturing of automotive components.