-
-
News
News Highlights
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueThe Hole Truth: Via Integrity in an HDI World
From the drilled hole to registration across multiple sequential lamination cycles, to the quality of your copper plating, via reliability in an HDI world is becoming an ever-greater challenge. This month we look at “The Hole Truth,” from creating the “perfect” via to how you can assure via quality and reliability, the first time, every time.
In Pursuit of Perfection: Defect Reduction
For bare PCB board fabrication, defect reduction is a critical aspect of a company's bottom line profitability. In this issue, we examine how imaging, etching, and plating processes can provide information and insight into reducing defects and increasing yields.
Voices of the Industry
We take the pulse of the PCB industry by sharing insights from leading fabricators and suppliers in this month's issue. We've gathered their thoughts on the new U.S. administration, spending, the war in Ukraine, and their most pressing needs. It’s an eye-opening and enlightening look behind the curtain.
- Articles
- Columns
- Links
- Media kit
||| MENU - pcb007 Magazine
Are There Advantages to Changing Your Registration System?
March 22, 2015 | Barry Matties, I-Connect007Estimated reading time: 9 minutes

I recently had a conversation with DIS's Tony Faraci at IPC APEX EXPO 2015, to learn more about their pinless registration system. What was most interesting to me are the potential advantages a pinless system offers and if so, why the process has not been widely adopted.
Barry Matties: Hello, Tony. Thanks for sitting down with me today. Could you please tell us about the DIS pinless registration system?
Tony Faraci: Yes, thanks, Barry. What is happening with this type of a system, as opposed to a conventional pin lamination technology, is that we are optically aligning all the internal layers of a panel. Conventional wisdom used to be that you would post-etch punch all your cores and then pin. Now, you are eliminating that whole process. You are eliminating pinning, you're eliminating all of that punching and all of that pin tooling and now we are optically aligning all the layers and tack bonding them together.
By optically aligning, all those mechanical pin tolerances are eliminated, and of course you are not limited to certain panel sizes. The layers are aligned optically and then we use an induction bonding system that actually bonds the layers together. The advantage here is that the registration can be checked before lamination, which really can't be done with any type of pinning system.
You can kind of do it with a riveting system, let's say, or eyelets, but with this type of system, now you can check your registration before going into the lamination press, then you laminate the panel, come out, and now you can again check the registration of that panel. Having the data immediately before and after lamination can show what's happening inside the press.
Besides this valuable data set, this is also telling you what our system is doing. It's giving you an overall view at different points of the process which they've never been able to do before. You can kind of do it with a riveting system but you're not going to do such high layer counts and it will not be repeatable. So DIS pinless technology is the next step up from pin because it eliminates all those mechanical problems.
Matties: For those who already have a pin system in place, are there any special processes or changes that they have to make?
Faraci: It changes a little bit in the process. What you're doing is using similar targets like they do on a punching machine, but now they are adding these welding coupons. They are just a quarter-inch by three-quarter-inch solid copper pads at four points on the panel that we'll use to tack bond.
Where it really changes is the reduced handling and lay-up. The machine is basically an optical lay-up machine, so instead of handling the panel once at post-etch punch and then going through oxide or oxide alternative, where there is some more stretching of the layer, and then laying up on mechanical pins, where most of the bulk error is, we’re only handling it once, at optical lay-up.
We're not selling a product that's competing against the post-etch punch; it's a process change. It eliminates that pin-up process and instead is optically aligning the layers; this really is the biggest change.
It's a little bit different in the process, so there is a learning curve. But the benefit for the customer is great, because now they can start looking at what's happening in the press. Today, most high-end shops work with pins, so what do they do, they lay up a book and you don't know if there's a shift -did it happen at lay-up, did it happen in the press, did it happen at transport?
So, that's one of the biggest changes. Another product that we developed about six years ago was a multi-camera system that allows us to check the layers front to back, in order to figure out where the best fit positions are for that layer. That also works well with our systems, because that data gets captured and it goes into our alignment systems.
Matties: How does that benefit?
Faraci: Let's say a customer is running higher-end boards. They can, if they have an LDI process for example, print a 2D bar code on every layer, serialize the core, and then our multi-camera system can actually measure that core and capture the positional data. And of course it's tied to that serial number.
Then when it gets to our alignment machines, they read that barcode and they know the positional data of that core, based on the eight targets, and now we can process the panel. So it enables all our existing two-camera machines—for example, what they have at DSG—once customers buy this unit, they’re able to have it work like an eight-camera system. Or you could use it off line just to measure panels to make sure that the layers are within tolerance before you use them at lay-up.
Matties: So, with your system the border is now smaller?Page 1 of 2
Suggested Items
The Evolution of Picosecond Laser Drilling
06/19/2025 | Marcy LaRont, PCB007 MagazineIs it hard to imagine a single laser pulse reduced not only from nanoseconds to picoseconds in its pulse duration, but even to femtoseconds? Well, buckle up because it seems we are there. In this interview, Dr. Stefan Rung, technical director of laser machines at Schmoll Maschinen GmbH, traces the technology trajectory of the laser drill from the CO2 laser to cutting-edge picosecond and hybrid laser drilling systems, highlighting the benefits and limitations of each method, and demonstrating how laser innovations are shaping the future of PCB fabrication.
Day 2: More Cutting-edge Insights at the EIPC Summer Conference
06/18/2025 | Pete Starkey, I-Connect007The European Institute for the PCB Community (EIPC) summer conference took place this year in Edinburgh, Scotland, June 3-4. This is the third of three articles on the conference. The other two cover Day 1’s sessions and the opening keynote speech. Below is a recap of the second day’s sessions.
Day 1: Cutting Edge Insights at the EIPC Summer Conference
06/17/2025 | Pete Starkey, I-Connect007The European Institute for the PCB Community (EIPC) Summer Conference took place this year in Edinburgh, Scotland, June 3-4. This is the second of three articles on the conference. The other two cover the keynote speeches and Day 2 of the technical conference. Below is a recap of the first day’s sessions.
Preventing Surface Prep Defects and Ensuring Reliability
06/10/2025 | Marcy LaRont, PCB007 MagazineIn printed circuit board (PCB) fabrication, surface preparation is a critical process that ensures strong adhesion, reliable plating, and long-term product performance. Without proper surface treatment, manufacturers may encounter defects such as delamination, poor solder mask adhesion, and plating failures. This article examines key surface preparation techniques, common defects resulting from improper processes, and real-world case studies that illustrate best practices.
RF PCB Design Tips and Tricks
05/08/2025 | Cherie Litson, EPTAC MIT CID/CID+There are many great books, videos, and information online about designing PCBs for RF circuits. A few of my favorite RF sources are Hans Rosenberg, Stephen Chavez, and Rick Hartley, but there are many more. These PCB design engineers have a very good perspective on what it takes to take an RF design from schematic concept to PCB layout.