Researchers Create Functional Ultrathin Solar Cells
August 27, 2015 | Phys.orgEstimated reading time: 1 minute
A team of researchers with Johannes Kepler University Linz in Austria has developed an ultrathin solar cell for use in lightweight and flexible applications. In their paper published in the journal Nature Materials, the group describes how they created their solar cells and then tested them with miniature aircraft.
For engineers working with solar cells, two major goals are increasing the amount of electricity that can be harvested from a single cell, and making cells thinner and lighter while still producing the same amount or even more electricity as thicker cells. In this new effort, the research team has found a way to produce a solar cell that is just three micrometers thick, yet is still 12 percent efficient.
To create thinner cells, scientists have turned to new materials, one of which is organolead halide perovskites. They are direct band semiconductors and thus absorb light more efficiently than other materials. Unfortunately, they are also much more sensitive to environmental conditions, deteriorating when exposed to water, and worse as they do so, they tend to cause problems for metal electrodes. To make solar cells out of such materials requires adding protective coatings, which of course cause the end result to be both thicker and heavier.
To make their ultrathin solar cells, the team used a chromium oxide–chromium interlayer to protect the metal contacts against problems with the perovskite, then applied a clear polymer electrode that had been treated with dimethylsulphoxide. The result was an extremely thin one square meter solar cell that weighed just 5.2 grams and was capable of producing 120 watts of power, which the team notes, is a record for power per weight solar cells.
To test their cells, the researchers attached them to a miniature plane and blimp, and report that the cells work as envisioned. The only problem of course, is that the cells have a short lifespan—they are still at the mercy of both water and oxygen because the coatings do not last very long, just a few days, though under optimal conditions they found that cells could survive for up to several months. Still, that may be long enough for some applications, such as weather balloons, drones, etc. especially those that are able to use other means for protecting them.
Suggested Items
KIC’s Miles Moreau to Present Profiling Basics and Best Practices at SMTA Wisconsin Chapter PCBA Profile Workshop
01/25/2024 | KICKIC, a renowned pioneer in thermal process and temperature measurement solutions for electronics manufacturing, announces that Miles Moreau, General Manager, will be a featured speaker at the SMTA Wisconsin Chapter In-Person PCBA Profile Workshop.
The Drive Toward UHDI and Substrates
09/20/2023 | I-Connect007 Editorial TeamPanasonic’s Darren Hitchcock spoke with the I-Connect007 Editorial Team on the complexities of moving toward ultra HDI manufacturing. As we learn in this conversation, the number of shifting constraints relative to traditional PCB fabrication is quite large and can sometimes conflict with each other.
Standard Of Excellence: The Products of the Future
09/19/2023 | Anaya Vardya -- Column: Standard of ExcellenceIn my last column, I discussed cutting-edge innovations in printed circuit board technology, focusing on innovative trends in ultra HDI, embedded passives and components, green PCBs, and advanced substrate materials. This month, I’m following up with the products these new PCB technologies are destined for. Why do we need all these new technologies?
Experience ViTrox's State-of-the-Art Offerings at SMTA Guadalajara 2023 Presented by Sales Channel Partner—SMTo Engineering
09/18/2023 | ViTroxViTrox, which aims to be the world’s most trusted technology company, is excited to announce that our trusted Sales Channel Partner (SCP) in Mexico, SMTo Engineering, S.A. de C.V., will be participating in SMTA Guadalajara Expo & Tech Forum. They will be exhibiting in Booth #911 from the 25th to the 26th of October 2023, at the Expo Guadalajara in Jalisco, Mexico.
Intel Unveils Industry-Leading Glass Substrates to Meet Demand for More Powerful Compute
09/18/2023 | IntelIntel announced one of the industry’s first glass substrates for next-generation advanced packaging, planned for the latter part of this decade.