Research Improves Conductive Plastic for Health, Energy
April 21, 2016 | Washington State UniversityEstimated reading time: 3 minutes
Biological implants that communicate with the brain to control paralyzed limbs or provide vision to the blind are one step closer to reality thanks to research by Brian Collins, an assistant professor of physics at Washington State University.
Collins and an international team of scientists developed methods to improve the performance of a conductive plastic that can be used in devices that interface with the human body. Sensors based on the material are superior in detecting and recording signals used by neurons in the brain.
The material also could be used for better energy storage in the next generation of battery technology and might find its way into other flexible future applications.
“Because this material is biocompatible, it could be used in a wide array of medical implants and other on-the-body technologies,” Collins said. “Circuits made with this polymer or another material like it could lead to clothing embedded with sensors, displays, even power sources, and might one day result in robotics that look, feel and even operate just like biological entities.”
Optimizing conduction in plastic
Conductive plastic, or polymer, is a relatively new material. Its precursors are commonly seen in organic light-emitting diode (OLED)-based television sets and cell phones. Unlike metal-based devices and circuitry, polymers are flexible, easily mass-produced and biocompatible.
They are made from earth abundant elements (carbon, nitrogen and oxygen) and can be printed from inks. The materials studied by Collins have two additional important qualities: They can conduct both the electrical and ionic signals that neurons in the brain use to communicate. These qualities are also critical for materials in batteries.
To date, the problem with polymer-based electronics has been a lack of understanding in how their nanostructure affects performance, and therefore how to optimize that performance. Because they are made up of low-density carbon and other light elements, polymers are hard to study at the nanoscale.
“To have a device that can interface with the brain, it would need to be sensitive enough to detect faint ionic signals of neuronal activity and then capable of converting these to electrical signals that can be interpreted by a computer,” Collins said. “Unfortunately, there are very few non-toxic commercial materials that can do this.
“With our research, it will be possible to achieve the critical capabilities of both types of conduction for polymer materials that can be used in the development of future devices,” he said.
‘Tuning’ materials for best performance
Collins studies the relation between the physical nanostructure and electrical properties of conductive polymers. A novel resonant x-ray scattering technique he developed as a researcher at the National Institute of Standards and Technology can uniquely probe molecular arrangements of polymer nanomaterials.
Using this technique, he was able to reveal how the arrangements can be controlled and tailored. His work was conducted using the Advanced Light Source at Lawrence Berkeley National Laboratory. His collaborators in the Department of Bioelectronics at the École Nationale Supérieure des Mines in France then used a new method to separately measure electrical and ionic conductivity to determine which of the molecular configurations performed the best.
“Devices based on these materials could result in medical breakthroughs similar to the recent report of limb reanimation,” Collins said, referring to Ian Burkhart of Ohio who, through a new experimental procedure involving neuron implants, can again articulate his fingers after being paralyzed for five years. “With our new ability to probe both polymer nanostructure and properties, it will be possible to tune materials for optimal performance in an array of novel technologies.”
The Advanced Light Source is supported by the Office of Basic Energy Sciences of the U.S. Department of Energy.
Suggested Items
The Shaughnessy Report: Unlock Your High-speed Material Constraints
05/15/2024 | Andy Shaughnessy -- Column: The Shaughnessy ReportThe world of PCB materials used to be a fairly simple one. It was divided into two groups: the “traditional” laminates, often called FR-4, and the high-speed laminates developed especially for high-speed PCBs. These were two worlds that usually didn’t collide. But then traditional laminates started getting better, and high-speed designers and design engineers took notice and started to reconsider what FR-4 could be used for.
Breaking High-speed Material Constraints: Design007 Magazine — May 2024
05/14/2024 | I-Connect007 Editorial TeamDo you need specialty materials for your high-speed designs? Maybe not. Improvements in resins mean designers of high-speed boards can sometimes use traditional laminate systems instead of high-speed materials, saving time and money while streamlining the fab process. In the May 2024 issue of Design007 Magazine, our contributors explain how to avoid overconstraining your materials when working with high-speed boards.
Indium Experts to Present at Electronics in Harsh Environments SMTA Conference
05/13/2024 | Indium Corporationndium Corporation Technical Manager for Europe, Africa, and the Middle East, Karthik Vijay, will deliver a technical presentation and Indium Corporation Senior Technologist, Dr. Ronald Lasky, will deliver both a workshop and technical presentation at the Electronics in Harsh Environments SMTA Conference on May 14-16 in Copenhagen, Denmark.
Ansys’ Collaboration with Schrödinger will Accelerate Materials Development with Unprecedented Multiscale Simulation
05/09/2024 | ANSYSAnsys and Schrödinger are collaborating to deliver an ICME approach that bridges the gap between materials discovery and product development.
2024 Apple iPad Pro Estimated to Ship Between 4.5 to 5 Million Units
05/08/2024 | TrendForceApple’s recent product launch in May introduced a lineup of new tablets featuring advanced AMOLED screens. Notably, the Pro version boasts a dual-layer tandem structure designed to address the longstanding challenges of screen burn-in and lifespan that are common with AMOLED displays.