Precision Measurements for Magnetic Memory
May 3, 2016 | DTUEstimated reading time: 2 minutes
MRAM is a memory type that combines the advantageous characteristics of three important memory solutions used in consumer electronics. This includes the high density of DRAM (dynamic RAM), the high speed of SRAM (static RAM) and the nonvolatile (i.e. the ability to retrieve stored information even after having been turned off and back on) storage of Flash memory.
The active part of an MRAM cell is a so called magnetic tunnel junction which uses the magnetic properties of electrons, i.e. the electron spin, to read and write magnetic information in the memory cell. The most critical part in such a magnetic tunnel junction is the electron transport properties across a dielectric layer, e.g. magnesium oxide, with a thickness of just 1 nm (a few atomic layers). Through the past decade these properties have been characterised using a measurement system developed by the DTU Nanotech spin-off company Capres A/S.
Towards a large scale production of MRAM
To produce a well-functioning memory device with hundreds of millions of MRAM cells, it is necessary to monitor precisely the electrical properties and as MRAM enters into large scale production, the requirements on metrology increase significantly. Measurement speed, precision and reliability must be improved compared to previous generations of metrology systems. Also, measurements must be possible on test structures available in production that may differ from test samples in product development. These issues have been addressed in a number of collaboration projects between Capres A/S and DTU Nanotech.
Senior Researcher Dirch Hjorth Petersen explains: “By detailed analysis of the metrology system, we have identified the most critical parameters and optimised the measurement routines accordingly. With this, we have been able to reduce measurement time by a factor of 5 and we have developed a methodology for a product specific measurement procedure”.
The customised procedure yields significant improvements in measurement precision as compared to previous state-of-the-art measurements. The measurement reliability is being improved through use of vibration tolerant electrodes for superior measurement stability, and early tests are encouraging. Finally, a model has been developed to allow measurements in small test pads relevant for production monitoring.
Co-founder and CTO at Capres A/S, Peter Folmer Nielsen states: “We expect the combination of improvements to pave the road for fully automated monitoring of product quality during MRAM production”.
The improvements have been achieved through collaboration between Industrial Postdocs Alberto Cagliani and Frederik W. Østerberg, former Industrial PhD student Daniel Kjær, as well as Senior Researcher Dirch H. Petersen and Professor Ole Hansen.
Suggested Items
Curtiss-Wright Awarded Contracts Valued in Excess of $130M to Support Critical U.S. Naval Defense Platforms
05/16/2024 | BUSINESS WIRECurtiss-Wright Corporation announced it has been awarded contracts valued in excess of $130 million to provide propulsion valves, pumps and advanced instrumentation and control systems for the U.S. Navy’s Virginia-class nuclear powered attack submarine, Columbia-class submarine and Ford-class aircraft carrier programs.
Flex Announces Upcoming Changes to Its Board of Directors
05/07/2024 | FlexFlex announced that consistent with its succession plan, Michael D. Capellas, non-executive Chair of the Board of Directors of Flex, has informed the Board of his decision not to stand for re-election to the Board at the company's 2024 Annual General Meeting of shareholders to be held on August 8, 2024. Mr. Capellas has served on the company's board for 10 years, including as Chair since 2017, during which time he played a key role in building Flex's reputation as a trusted global technology, supply chain and manufacturing solutions partner and driving the company's success.
Europlacer Presents New Range of iineo SMT Placement Machines.
05/01/2024 | EuroplacerFor more than 15 years, the Europlacer iineo placement machines have made their mark on the SMT industry with unique features and unrivalled flexibility. Today, Europlacer announces the launch of the second generation iineo.
Incap US Hosts Annual Food Drive
04/30/2024 | IncapIncap US recently concluded its annual food drive, a tradition aimed at supporting the Greater Washington County Food Bank. This year marked the fourth year of the initiative, and we couldn’t be prouder of the collective effort that was made to its success.
Scanfil Uses Employee Engagement Survey to Improve
04/30/2024 | ScanfilOnce a year Scanfil arranges Employee Engagement Survey (EES) in order to get valuable insight from its employees. In EES all employees are invited to share their opinion, bring ideas for improvements, and contribute to making Scanfil a better place to work.