Frequency Stabilization of Magnetic Tunnel Junction Based Microwave Oscillator
June 28, 2016 | AISTEstimated reading time: 3 minutes
Shingo Tamaru (Invited Senior Researcher), the Metal Spintronics Team, the Spintronics Research Center (SRC; Director: Shinji Yuasa), the National Institute of Advanced Industrial Science and Technology (AIST; President: Ryoji Chubachi) and Hitoshi Kubota (Principle Research Manager) and Akio Fukushima (Deputy Director), SRC, AIST, have developed a phase locked loop (PLL) circuit designed to stabilize the oscillation frequency of a spin torque oscillator (STO), and demonstrated generation of a highly coherent microwave signal from the STO.
The STO is a nanometer-scale magnetoresistive device that generates a microwave signal by applying a DC voltage. The 7.344 GHz microwave signal generated by the STO was phase locked to a 153 MHz reference signal by the developed PLL circuit, resulting in an extremely narrow spectral linewidth of below the measurement limit (1 Hz). The narrowest spectral linewidth of the microwave signal generated by a single magnetic tunnel junction (MTJ) based STO reported thus far has been 3 MHz achieved by AIST. The developed PLL circuit led to a dramatic improvement of the frequency stability of the STO oscillation. This accomplishment is expected to accelerate the progress toward the practical use of STOs as a voltage controlled oscillator (VCO).
Social Background of Research
Recently, various microwave communication devices, such as cellular phone and wireless LAN, have been widespread, in which VCOs composed of semiconductor transistors and resonators are used. The resonator used in the conventional VCO has a size of as large as a few 100 μm, which is one of major obstacles for further miniaturization and cost reduction. On the other hand, the STO is a nanometer-scale magnetoresistive device requiring no external resonator, thus attracting significant attention as an ultra-small VCO compared with the conventional ones. However, the frequency stability of the STO is quite poor, hampering adoption of the STOs in real electronics systems.
History of Research
AIST have been working on developing thin film deposition and microfabrication technologies for STOs by applying knowledge and experience gained through the research on spintronic memory devices. In order to use an STO in various practical applications, it has to show both large output power and high frequency stability. For this goal, the researchers have been focusing on realizing a stable oscillation of an STO based on MTJ, which has a high magnetoresistance ratio. They have already achieved the world highest output power at that time and the world best frequency stability of an output signal from a single STO (AIST press releases on Aug. 28, 2008 and Jan. 8 2014).
This work has been partially supported by the Grant-in-Aid for Scientific Research (S) “Research and Development of High Frequency Spintronics” of the Japan Society for the Promotion of Science.
Details of Research
In order to realize a good enough frequency stability of an MTJ based STO for practical uses, the researchers improved oscillation characteristics of an STO and developed a PLL circuit designed to stabilize the oscillation frequency of the STO. The STO used in this work was fabricated out of a MTJ consisting of an ultra-thin MgO tunnel barrier of about 1 nm and amorphous magnetic alloy layers containing Fe. The interface between the MgO and magnetic alloy layer tends to align spins along the direction perpendicular to the interface plane. The spin precession trajectory was stabilized by utilizing this interface property. The oscillation frequency of this STO shifts lower as the applied voltage is increased. Figure 1 shows a block diagram and a photo of the PLL circuit. In this PLL circuit, the STO output signal is downcounted by 48, and its phase is compared with that of the 153 MHz reference signal. The phase difference between these two signals is converted to a voltage signal, and fed back to the STO to tune the oscillation frequency dynamically such that the phase difference is always minimized. The high frequency spurious signals contained in the feedback signal, which disturbs the STO oscillation, are blocked by a filter for stable feedback operation.
Future Plans
The oscillation performance of the STO, especially frequency tunability by voltage, will further be improved and PLL circuit design will be refined for higher frequency response in order to develop a higher performance STO based microwave oscillator. These efforts should lead to practical use of the STO as an ultra-small and low cost microwave oscillator.
Suggested Items
Europlacer Presents New Range of iineo SMT Placement Machines.
05/01/2024 | EuroplacerFor more than 15 years, the Europlacer iineo placement machines have made their mark on the SMT industry with unique features and unrivalled flexibility. Today, Europlacer announces the launch of the second generation iineo.
Incap US Hosts Annual Food Drive
04/30/2024 | IncapIncap US recently concluded its annual food drive, a tradition aimed at supporting the Greater Washington County Food Bank. This year marked the fourth year of the initiative, and we couldn’t be prouder of the collective effort that was made to its success.
Scanfil Uses Employee Engagement Survey to Improve
04/30/2024 | ScanfilOnce a year Scanfil arranges Employee Engagement Survey (EES) in order to get valuable insight from its employees. In EES all employees are invited to share their opinion, bring ideas for improvements, and contribute to making Scanfil a better place to work.
epoxySet Introduces EO-20E – Versatile, Electrically Conductive Epoxy
04/29/2024 | epoxySetepoxySet produces EPOXIOHM EO-20E an industry established, reliable electrically conductive epoxy designed for solder replacement, chip bonding and other intricate electronic and optoelectronic assemblies. This creamy paste has a an easy to use 1:1 mix ratio with a 48 hour work time.
The Right Approach: I Hear the Train A Comin'
04/25/2024 | Steve Williams -- Column: The Right ApproachTraining is often an afterthought in many organizations, and the longer a company has been in business, the more this seems to apply. Over the past couple of decades, it has been amazing to observe that the biggest offenders of this are the companies that overuse the sound bite, “Our most important assets are our people.” When you dig into the process and peel back the onion, their commitment to training is not commensurate with that statement.