Knocking Down the Bone Pile: Gold Mitigation for Class 2 Electronics
Punching Out: Your Financial Preparation for a Sale
Nolan's Notes: The Next Killer App in Component Manufacturing
The Complex World of Soldering
May 1, 2017 | Stephen Las Marias, I-Connect007Estimated reading time: 11 minutes
Las Marias: What else do you think should the readers know more about when it comes to soldering?
Holden: Some of the effects that different formulations of lead-free solder paste has when it's reflowed, in terms of interacting with final finish and interacting with land size, is that they don’t spread like tin lead, and we find smaller pad sized footprints because it’s a stronger joint than tin lead. We’ve always watched very closely the Japanese and the JPCA standards, because they’ve been using lead free for 10 years longer than North America. Since a third of all of our output goes to Japanese automakers, we’ve got a lot of cooperation with Nissan, Honda, and Toyota about what they recommend.
Las Marias: Standardization is still an issue?
Holden: It's all a point of view. Like I said, we're such as big industry that I’ve been talking about automotive electronics, which were going for a 15-year useful life—and that’s a lot different than a mobile phone. We virtually test 100% of every lot because the Japanese or the German auto companies insist on that. If we ever have a failure, we have to go back into root cause analysis. A lot of my experience deals with reliability because warranty failures and things like that is a big bug-a-boo in automotive. But depending on which industry you’re in, there's a lot of differences. Most mobile phones don't make it past two years before they've been dropped in the toilet, run over, or just that everybody turns them in for the new models.
You have to support your customers, and not all customers have the same needs. It’s the final performance that our customers required. They weren’t dictating a design or a process, only the final performance, whereas if you're an EMS and you have multiple customers, you have to keep shifting it all the time depending on what the requirements are. We still have wave solder machines. They're lead free, but they’re still wave solder.
Cox: We do too. We do a lot of military and oil and gas that we build predominantly through-hole. We have a lead one and a lead free.
Holden: Lead free is a lot tougher than the tin lead.
Cox: Yes. I was thinking about it and a lot of what I've experienced here in the last couple of years is our customers will sometimes call out to use a lead-free no clean solder on their boards. Then they are upset with us that their boards do not look clean and the solder looks to be disturbed. Really, the industry needs to know having a lead-free solder is going to look more grimy than using leaded solder. They look different. A no-clean solder doesn't necessarily mean that it's going to be clean. You're going to have residue there, but it's not active flux residue. The different types of solder that you run into along the way, whoever you use should talk to you about the way your solder is going to look before you actually put it on the boards. I think that’s a big thing. Our customers come back and say the boards are dirty, but they’re not. They meet IPC standards and they use a no-clean flux, which will leave slight residue on their boards.
Holden: That's one thing I can't ever remember reading or seeing: a breakdown of the soldering industry by what all of the different types of solders look like, in terms of a picture, whether clean or no clean. Then, their interaction with final finishes, and then what industries they are preferred by in terms of a matrix. A lot of people tend to get confused, because if you're talking about the communications industry, that may not apply to the consumer industry; or when we're talking about automotive, that might not apply to medical. You haven't always seen these things. Nobody’s ever come out and given us matrix of what they’re supposed to look like, and maybe what the estimated life is in terms of their interaction with land patterns, with final finishes, and with percent of voiding. That chart or definitive explanation has not been out there.
Cox: I agree. A lot of customers I know say, ‘Oh, if I have the choice between the no clean or the aqueous, I want to go with the no clean because that means my board will be clean.’ But in reality, it means that you don't need to clean the board because the residue that's left isn't active. You will actually have a cleaner board, appearance-wise, if you use an aqueous flux. Then you can wash it and there is nothing left behind. That’s something we struggle with over here a lot with our customers. It's just a miscommunication of what they're actually using, what the product is doing, and how it's going to look.
Las Marias: Cathy and Happy thank you so much again for your time and your insights.
Cox: Thank you.
Holden: Sure.
Page 2 of 2Share on:
Suggested Items
Hunting for Clues: Feng Xue Solving Circuit Board 'Crimes' With AOI Standard
05/08/2025 | Linda Stepanich, IPCWhen residents in sleepy English villages needed a top-tier detective to solve a murder, they called on Belgian super-sleuth Hercule Poirot, author Agatha Christie’s fictional detective famous for using his “little grey cells” to solve crimes. In the same way, IPC standards development committees, when creating a standard to detect defects in circuit boards using Automated Optical Inspection (AOI), call on IPC A-Team, Hercule.
IPC Strengthens Global Focus with Promotion of Sanjay Huprikar to Chief Global Officer
05/08/2025 | IPCIPC, the global electronics association, announces the promotion of Sanjay Huprikar to chief global officer. This newly created position reflects the association’s forward-looking strategy and industry needs to strengthen the electronics supply chain.
Navigating Global Manufacturing in an Era of Uncertainty
05/07/2025 | Philip Stoten, ScoopThe EMS industry faces unprecedented challenges as global trade tensions rise and tariff announcements create market uncertainty. In an overview of IPC Europe’s podcast, MADE IN EUROPE, industry experts from GPV and Zollner examine how these developments impact our businesses and customers, and what strategies will prevail in this new landscape.
Nick Koop Launches IPC Flex Design Class
05/06/2025 | Andy Shaughnessy, Design007 MagazineNick Koop is director of flex technology for TTM Technologies, and he’s been a staple of IPC’s flex committees for decades. He’s also a longtime flex design instructor, and he’s about to debut a new IPC class, Flex and Rigid-Flex Design for Manufacturability, which will run May 12–21. In this interview, Nick tells us about this new class and what attendees can expect to learn.
The Government Circuit: Trump’s Trade War Disrupts the Electronics Ecosystem
05/06/2025 | Chris Mitchell -- Column: The Government CircuitThere is certainly no shortage of work to be done in the IPC Government Relations department, as the U.S. waged a tariff campaign on practically every industrial country in the world and several countries embarked on high-tech initiatives with a mix of approaches to the crucial foundations of electronics manufacturing. Indeed, the breadth and speed of U.S. President Donald Trump’s tariff campaign continues to be a serious challenge for our industry.