Dan's Biz Bookshelf: 'Move Your Bus'
Driving Innovation: Direct Imaging vs. Conventional Exposure
It’s Only Common Sense: Selling to Today's Generation of Buyers
X-Ray Inspection of Lead and Lead-Free Solder Joints
July 31, 2017 | Glen Thomas, Ph.D., and Bill Cardoso, Ph.D., Creative Electron Inc.Estimated reading time: 13 minutes
where Emax is the maximum energy in the spectrum, which is 150keV for the X-ray machine used in this paper.
TIN-LEAD SOLDER VS. LEAD-FREE SOLDERS
There are a number of lead-free solder compounds in the market today. For examples in this analysis we used some of the solder compounds discussed in [5]. In particular, we compare eutectic tin-lead solder (63Sn/37Pb), tin-bismuth (42Sn/58Bi), and a variety of predominantly tin based solders, including tin-silver (98Sn/2Ag), tin-antimony (95Sn/5Sb), tin-indium-silver (77.2Sn/10In/2.8Ag), and tin-silver-copper (96.3Sn/3.2Ag/0.5Cu).
Solder compounds can be classified according to those he deems most likely lead-free alternatives, all of which have at least 95% Sn content[5]. In our analysis, we consider three of these (98Sn/2Ag, 95Sn/5Sb, and 96.3Sn/3.2Ag/0.5Cu). The others are provided for comparison purposes. Equation 4 must be discretized for evaluation. Using a Creative Electron’s proprietary emulation and simulation software, we computed the energy spectra and attenuation coefficients for 16 bands of 10keV width spanning 10keV to 160keV. Equation 4 in discrete form then becomes:
Using this data and accounting for filtration due to the X-ray source anode materials, we obtain values for all p(Ei ). The results are summarized in Figure 5. In Figure 6 we provide the stopping power (i.e., 1-I/I0) for five lead-free solder compounds and eutectic tin-lead solder at thicknesses of 2 mil, 5 mil, 10 mil, and 20 mil. The stopping power indicates the relative amount of X-rays that are attenuated in the material. For example, a stopping power of 0.75 means that three-quarters of the incident radiation is attenuated. Higher numbers consequently imply higher attenuation.
Figure 5: Energy spectrum of a TruView FUSION with a 150kV microfocus X-ray source.
Figure 6: Attenuation of lead-free solders and eutectic tin-lead solder. Note that the amount of attenuation at different material thicknesses is similar.
X-RAY IMAGE ANALYSIS
To validate the analysis presented in the previous session our Advanced Technology Group inspected a wide range of samples with both lead and lead-free solder composites. We compared eutectic tin-lead (63Sn/37Pb) and tin-bismuth (42Sn/58Bi) solders for their imaging profile using a TruView FUSION running at a maximum of 150kV. As expected, the X-ray images obtained from the samples using both types of solder did not present a notable difference. Please note that it is not the focus of this paper to compare the overall performance between lead and lead-free solders. Instead, the objective of this analysis is to validate that the X-ray machine settings work for both lead and lead-free solders.
Figure 7: Gullwing solder joints using both lead and leadfree solder paste. Note that the lead-free solder is slightly lighter (less dense) than the lead solder joint.
Page 3 of 5
Share on:
Suggested Items
Driving Innovation: Direct Imaging vs. Conventional Exposure
07/01/2025 | Simon Khesin -- Column: Driving InnovationMy first camera used Kodak film. I even experimented with developing photos in the bathroom, though I usually dropped the film off at a Kodak center and received the prints two weeks later, only to discover that some images were out of focus or poorly framed. Today, every smartphone contains a high-quality camera capable of producing stunning images instantly.
Hands-On Demos Now Available for Apollo Seiko’s EF and AF Selective Soldering Lines
06/30/2025 | Apollo SeikoApollo Seiko, a leading innovator in soldering technology, is excited to spotlight its expanded lineup of EF and AF Series Selective Soldering Systems, now available for live demonstrations in its newly dedicated demo room.
Indium Corporation Expert to Present on Automotive and Industrial Solder Bonding Solutions at Global Electronics Association Workshop
06/26/2025 | IndiumIndium Corporation Principal Engineer, Advanced Materials, Andy Mackie, Ph.D., MSc, will deliver a technical presentation on innovative solder bonding solutions for automotive and industrial applications at the Global Electronics A
Fresh PCB Concepts: Assembly Challenges with Micro Components and Standard Solder Mask Practices
06/26/2025 | Team NCAB -- Column: Fresh PCB ConceptsMicro components have redefined what is possible in PCB design. With package sizes like 01005 and 0201 becoming more common in high-density layouts, designers are now expected to pack more performance into smaller spaces than ever before. While these advancements support miniaturization and functionality, they introduce new assembly challenges, particularly with traditional solder mask and legend application processes.
Knocking Down the Bone Pile: Tin Whisker Mitigation in Aerospace Applications, Part 3
06/25/2025 | Nash Bell -- Column: Knocking Down the Bone PileTin whiskers are slender, hair-like metallic growths that can develop on the surface of tin-plated electronic components. Typically measuring a few micrometers in diameter and growing several millimeters in length, they form through an electrochemical process influenced by environmental factors such as temperature variations, mechanical or compressive stress, and the aging of solder alloys.