The Knowledge Base: The Era of Advanced Packaging
Standard of Excellence: Finding and Developing Future Leaders in Manufacturing
Global Sourcing Spotlight: Navigating the Variables of Holiday Schedules in Global Sourcing
CyberOptics to Demo CMM Powered by MRS Tech at NEPCON China
March 28, 2018 | CyberOptics CorporationEstimated reading time: 1 minute
CyberOptics Corporation will exhibit in Stand 1F32 at NEPCON China, scheduled to take place April 24-26, 2018 at the Shanghai World EXPO Exhibition & Convention Center. Company representatives will demonstrate the new high-speed SQ3000 3D CMM, an extension of the MRS-enabled SQ3000 platform deemed best-in-class, along with the new MRS-enabled SE3000 SPI system.
The new SQ3000 3D CMM (Coordinate Measurement) system, powered by Multi-Reflection Suppression (MRS) technology utilizes CyberCMM, a new comprehensive software suite for coordinate measurement. In a lab or production environment, the MRS-enabled SQ3000 CMM system is extremely fast and highly accurate, with repeatable and reproducible measurements for metrology applications in manufacturing of a wide variety of products such as PCBs, semiconductors and consumer electronics.
CyberCMM, an extensive suite of CMM tools, provides 100 percent metrology-grade measurement on all critical points much faster than a traditional CMM – seconds, not hours – including coplanarity, distance, height and datum X, Y, to name a few. A fast and easy setup can be performed as compared to a slow, engineering resource-intensive setup that typically requires multiple adjustments with traditional CMMs.
The new SE3000 SPI system is the very first SPI system to incorporate the industry-leading MRS sensor technology with a finer resolution for the best accuracy, repeatability and reproducibility – even on the smallest paste deposits. Combined with the award-winning, easy-to-use software, solder paste inspection has reached a new level of precision for the most stringent requirements.
About CyberOptics
CyberOptics Corporation is a leading global developer and manufacturer of high precision sensing technology solutions. CyberOptics sensors are being used in general purpose metrology and 3D scanning, surface mount technology (SMT) and semiconductor markets to significantly improve yields and productivity. By leveraging its leading edge technologies, the company has strategically established itself as a global leader in high precision 3D sensors, allowing CyberOptics to further increase its penetration of its key vertical markets. Headquartered in Minneapolis, Minnesota, CyberOptics conducts worldwide operations through its facilities in North America, Asia and Europe. For more information, click here.
Share on:
Suggested Items
Book Excerpt: The Printed Circuit Assembler’s Guide to... Low-Temperature Soldering, Vol. 2, Chapter 5
12/23/2024 | I-Connect007 Editorial TeamChapter 5 introduces the advantages of using low-temperature soldering for through-hole components, including cost efficiency, reliability improvement, and reduced warpage. Also covered: the evaluation of different fluxes and the performance of HRL3 in wave soldering and selective soldering processes.
Overview of Soldering Systems With Vacuum
12/18/2024 | Dr. Paul Wild, Rehm Thermal Systems GmbHWhen soldering electronic assemblies, the focus of the vacuum application is on the removal of volatile substances from the solder joints and the associated reduction of pore formation. Particularly in the thermal management of power electronics components, pores can cause so-called hotspots with higher temperatures due to their poor heat conduction. These hotspots can lead to overheating of the components on the one hand and to thermally induced destruction of the solder structure on the other.
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
12/13/2024 | Andy Shaughnessy, I-Connect007This week, Peter Tranitz discusses the upcoming Pan-European Electronics Design Conference, set for Jan. 29-30 in Vienna, Austria. Pete Starkey brings us a review of the most recent EIPC Technical Snapshot webinar, which featured a global PCB maker update by Dr. Hayao Nakahara. Don't miss our interview with Manfred Huschka, who explains how companies can begin their own China Plus One plan. Stan Farnsworth breaks down photonic soldering and discusses its use in soldering materials that are not typically compatible. I also enjoyed Dan Beaulieu’s discussion on the value of consistency, and why just showing up for work is half the battle, especially in an inconsistent, evolving industry like ours.
Advancing Photonic Soldering
12/11/2024 | Nolan Johnson, SMT007 MagazineStan Farnsworth, director of customer satisfaction at PulseForge, discusses the advancements in photonic soldering that highlight its energy efficiency and versatility. Over the past two years, the company has refined its applications for flexible substrates and energy reduction, finding that photonic soldering allows the processing of materials that typically aren’t thermally compatible and offers significant energy savings compared to traditional methods.
Indium Introduces New ROL0 and Halogen-free Flux-cored Wire
12/11/2024 | Indium CorporationIndium Corporation announced the global availability of CW-807RS, a new high-reliability, halide- and halogen-free flux-cored wire that improves wetting speeds and cycle times for electronics assembly and robot soldering applications.