Low-cost Plastic Sensors Could Monitor a Range of Health Conditions
June 25, 2018 | University of CambridgeEstimated reading time: 3 minutes
An international team of researchers have developed a low-cost sensor made from semiconducting plastic that can be used to diagnose or monitor a wide range of health conditions, such as surgical complications or neurodegenerative diseases.
The sensor can measure the amount of critical metabolites, such as lactate or glucose, that are present in sweat, tears, saliva or blood, and, when incorporated into a diagnostic device, could allow health conditions to be monitored quickly, cheaply and accurately. The new device has a far simpler design than existing sensors, and opens up a wide range of new possibilities for health monitoring down to the cellular level.
The device was developed by a team led by the University of Cambridge and King Abdullah University of Science and Technology (KAUST) in Saudi Arabia. Semiconducting plastics such as those used in the current work are being developed for use in solar cells and flexible electronics, but have not yet seen widespread use in biological applications.
“In our work, we’ve overcome many of the limitations of conventional electrochemical biosensors that incorporate enzymes as the sensing material,” said lead author Dr Anna-Maria Pappa, a postdoctoral researcher in Cambridge’s Department of Chemical Engineering and Biotechnology. “In conventional biosensors, the communication between the sensor’s electrode and the sensing material is not very efficient, so it’s been necessary to add molecular wires to facilitate and ‘boost’ the signal.”
To build their sensor, Pappa and her colleagues used a newly-synthesised polymer developed at Imperial College that acts as a molecular wire, directly accepting the electrons produced during electrochemical reactions. When the material comes into contact with a liquid such as sweat, tears or blood, it absorbs ions and swells, becoming merged with the liquid. This leads to significantly higher sensitivity compared to traditional sensors made of metal electrodes.
Additionally, when the sensors are incorporated into more complex circuits, such as transistors, the signal can be amplified and respond to tiny fluctuations in metabolite concentration, despite the tiny size of the devices.
Initial tests of the sensors were used to measure levels of lactate, which is useful in fitness applications or to monitor patients following surgery. However, according to the researchers, the sensor can be easily modified to detect other metabolites, such as glucose or cholesterol by incorporating the appropriate enzyme, and the concentration range that the sensor can detect can be adjusted by changing the device’s geometry.
“This is the first time that it’s been possible to use an electron accepting polymer that can be tailored to improve communication with the enzymes, which allows for the direct detection of a metabolite: this hasn’t been straightforward until now,” said Pappa. “It opens up new directions in biosensing, where materials can be designed to interact with a specific metabolite, resulting in far more sensitive and selective sensors.”
Since the sensor does not consist of metals such as gold or platinum, it can be manufactured at a lower cost and can be easily incorporated in flexible and stretchable substrates, enabling their implementation in wearable or implantable sensing applications.
“An implantable device could allow us to monitor the metabolic activity of the brain in real time under stress conditions, such as during or immediately before a seizure and could be used to predict seizures or to assess treatment,” said Pappa.
The researchers now plan to develop the sensor to monitor metabolic activity of human cells in real time outside the body. The Bioelectronic Systems and Technologies group where Pappa is based is focused on developing models that can closely mimic our organs, along with technologies that can accurately assess them in real-time. The developed sensor technology can be used with these models to test the potency or toxicity of drugs.
The research was funded by the Marie Curie Foundation, the KAUST Office of Sponsored Research, and the Engineering and Physical Sciences Research Council.
Suggested Items
EMA Webinar: Maximize Your Design Productivity in OrCAD X and Allegro X
09/26/2024 | EMA Design AutomationLearn how the extensible environment in Cadence OrCAD X and Allegro X is being used to enhance and customize the PCB design flow in a webinar held by EMA on Tuesday, October 1st, 2024 @ 11am ET.
IDC Tracker: Used Smartphone Shipments Grew 6.4% in 2023 as Secondary Market Thrives Globally
09/25/2024 | IDCMore than 195 million used smartphones, including officially refurbished and used smartphones, were shipped into the market in 2023, an increase of 6.4% compared to 2022. The value of these shipments was $72.9 billion, up 12.4% year over year, according to data from the newly launched Worldwide Quarterly Used Device Tracker from International Data Corporation (IDC).
Book Excerpt: The Printed Circuit Designer’s Guide to... Thermal Management with Insulated Metal Substrates, Vol. 2, Chapter 4
09/25/2024 | I-Connect007 Editorial TeamDirect-bonded copper (DBC) with a ceramic base is a commonly used assembly technology. While advantages include excellent solder crack compensation due to similar CTE values between component and substrate, the construction is fragile and therefore places limits on size and exposure to vibration. Small assemblies in basic shapes such as a rectangle can be done, although larger, more complex shapes become difficult.
Installed Base of Wireless Devices in Industrial Automation Reached 56.5 Million in 2023
09/11/2024 | Berg InsightA new research report from the IoT analyst firm Berg Insight says that annual shipments of wireless devices for industrial automation applications reached 10.7 million units worldwide in 2023, accounting for approximately 9 percent of all new connected nodes.
A Parametric Approach to the Environmental Impact of PCB Fabrication
09/09/2024 | Maarten Cauwe, imecSustainability for electronics is receiving more attention due to environmental concerns, regulatory obligations, and to ensure competitiveness in a growing market for sustainable products. To facilitate the discussion on the environmental impact of electronics, there is a strong need for data on energy use, carbon footprint, greenhouse gas (GHG) emissions, hazardous chemicals used during manufacturing, waste generation, etc.