The Knowledge Base: The Era of Advanced Packaging
Standard of Excellence: Finding and Developing Future Leaders in Manufacturing
Global Sourcing Spotlight: Navigating the Variables of Holiday Schedules in Global Sourcing
Indium Corporation Expert to Present at EPCON Asia
September 22, 2020 | Indium CorporationEstimated reading time: 2 minutes
Indium Corporation’s Vice President of Technology, Dr. Ning-Cheng Lee, will be one of five workshop trainers at the Electronic Packaging Convention Asia 2020 (EPCON Asia), Oct. 6-8 and 12-14.
Dr. Lee will host three workshops, one each day from Oct. 12-14:
- Achieving High-Reliability of Solder Joints—In this course, Part 1 will address electromigration issues at the die-attach level of high-power devices; Part 2 will address the solder joint behavior based on fundamental material properties, as well as failure modes, with an emphasis on lead-free solder joints.
- Choosing Solders for the New Era—This workshop is presented in two parts and will explore emerging challenges of the rapidly evolving electronics assembly industry in order to ensure one’s success in this fiercely competitive environment. The first section will address cost and reliability and the second will address low-temperature soldering.
- DFx for Advanced Soldering Technology—With abundant case studies illustrating the principle and application of design for manufacturability (DFM) and design for reliability (DFR) in advanced soldering technology, this workshop will discuss both the SMT design and process needed to achieve high yield and high-reliability very easily, while also preparing for emerging challenges.
Dr. Lee has been with Indium Corporation since 1986. He has more than three decades of experience in the development of fluxes, alloys, and solder pastes for SMT industries. He has extensive experience in the development of high-temperature polymers, encapsulates for microelectronics, underfills, and adhesives. In addition to SMT and semiconductor soldering materials, his research also extends to nanobonding technology and thermally conductive materials. Dr. Lee has been recognized by numerous industry organizations for his research, including SMTA, IEEE, and CPMT, and he is an IEEE fellow. Dr. Lee has published articles in numerous industry publications and is frequently an invited speaker for presentations, seminars, keynote speeches, and short courses worldwide, many of which have been recognized with “Best of Conference” awards.
EPCON Asia is an annual convention and workshop series held in Penang—the hub of Malaysia’s electronics industry zone. The event provides professionals in the semiconductor and electronics manufacturing sectors with the opportunity to advance their technical understandings and discover innovative solutions to their industrial challenges by bringing together subject matter experts, professionals, and international authorities from the emerging electronics world to share their insights. The key themes of this year’s workshop include surface-mount technology, printed circuit board assembly, IC packaging, process optimization, yield improvement, and smart manufacturing.
Indium Corporation is a premier materials refiner, smelter, manufacturer, and supplier to the global electronics, semiconductor, thin-film, and thermal management markets. Products include solders and fluxes; brazes; thermal interface materials; sputtering targets; indium, gallium, germanium, and tin metals and inorganic compounds; and NanoFoil®. Founded in 1934, the company has global technical support and factories located in China, India, Malaysia, Singapore, South Korea, the United Kingdom, and the USA.
For more information about Indium Corporation, visit www.indium.com or email jhuang@indium.com.
Share on:
Suggested Items
Book Excerpt: The Printed Circuit Assembler’s Guide to... Low-Temperature Soldering, Vol. 2, Chapter 5
12/23/2024 | I-Connect007 Editorial TeamChapter 5 introduces the advantages of using low-temperature soldering for through-hole components, including cost efficiency, reliability improvement, and reduced warpage. Also covered: the evaluation of different fluxes and the performance of HRL3 in wave soldering and selective soldering processes.
Overview of Soldering Systems With Vacuum
12/18/2024 | Dr. Paul Wild, Rehm Thermal Systems GmbHWhen soldering electronic assemblies, the focus of the vacuum application is on the removal of volatile substances from the solder joints and the associated reduction of pore formation. Particularly in the thermal management of power electronics components, pores can cause so-called hotspots with higher temperatures due to their poor heat conduction. These hotspots can lead to overheating of the components on the one hand and to thermally induced destruction of the solder structure on the other.
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
12/13/2024 | Andy Shaughnessy, I-Connect007This week, Peter Tranitz discusses the upcoming Pan-European Electronics Design Conference, set for Jan. 29-30 in Vienna, Austria. Pete Starkey brings us a review of the most recent EIPC Technical Snapshot webinar, which featured a global PCB maker update by Dr. Hayao Nakahara. Don't miss our interview with Manfred Huschka, who explains how companies can begin their own China Plus One plan. Stan Farnsworth breaks down photonic soldering and discusses its use in soldering materials that are not typically compatible. I also enjoyed Dan Beaulieu’s discussion on the value of consistency, and why just showing up for work is half the battle, especially in an inconsistent, evolving industry like ours.
Advancing Photonic Soldering
12/11/2024 | Nolan Johnson, SMT007 MagazineStan Farnsworth, director of customer satisfaction at PulseForge, discusses the advancements in photonic soldering that highlight its energy efficiency and versatility. Over the past two years, the company has refined its applications for flexible substrates and energy reduction, finding that photonic soldering allows the processing of materials that typically aren’t thermally compatible and offers significant energy savings compared to traditional methods.
Indium Introduces New ROL0 and Halogen-free Flux-cored Wire
12/11/2024 | Indium CorporationIndium Corporation announced the global availability of CW-807RS, a new high-reliability, halide- and halogen-free flux-cored wire that improves wetting speeds and cycle times for electronics assembly and robot soldering applications.