The Knowledge Base: A Conference for Cleaning and Coating of Mission-critical Electronics
Defense Speak Interpreted: Is DARPA Still Around After CHIPS?
Beyond the Board: Orbital High Ground—Why Space Superiority Is Slipping Away
Airbus Achieves Eurodrone’s Preliminary Design Review
May 16, 2024 | AirbusEstimated reading time: 1 minute
The Eurodrone programme has successfully performed the Preliminary Design Review (PDR). Led by Airbus Defence and Space as prime contractor, this major programme milestone has been completed with OCCAR and representatives of the four customer nations (France, Germany, Italy and Spain) in the presence of the three Major Sub-Contractors (MSC), Airbus Defence and Space Spain, Dassault Aviation and Leonardo.
The PDR proves that the initial design of the aircraft has consistently matured, paving the way to proceed with the detailed design. It is the outcome of different technical assessments and evaluations conducted, such as Wind Tunnel Testing to confirm the aerodynamic configuration of Eurodrone, the overall design to ensure demonstration of operational capability, and the validation of a fully representative Digital Twin. From the very beginning, the Eurodrone programme benefits from both design philosophies – physical and digital.
Supported by and based on the knowledge already gathered, the Eurodrone programme enters into a new phase to reach the Critical Design Review (CDR), which will represent the final step and closure of architecture and system design.
“Performing the Preliminary Design Review for the development of Eurodrone represents an important step forward for this key European defence programme”, said Jean-Brice Dumont, Head of Air Power at Airbus Defence and Space. “It shows a real joint effort and collaborative spirit from all industrial partners and the Customer community to ensure European sovereignty and independence in this critical segment of unmanned long endurance ISTAR capability.”
Provided with innovative cutting-edge technology and designed to become one of the main pillars of any future combat air system, the Eurodrone will be an indispensable capability to facilitate international conflict prevention and crisis management, ensuring operational superiority to the nations, especially in the context of Intelligence, Surveillance, Target Acquisition and Reconnaissance (ISTAR) missions.
Share on:
Suggested Items
Digital Twin Concept in Copper Electroplating Process Performance
07/11/2025 | Aga Franczak, Robrecht Belis, Elsyca N.V.PCB manufacturing involves transforming a design into a physical board while meeting specific requirements. Understanding these design specifications is crucial, as they directly impact the PCB's fabrication process, performance, and yield rate. One key design specification is copper thieving—the addition of “dummy” pads across the surface that are plated along with the features designed on the outer layers. The purpose of the process is to provide a uniform distribution of copper across the outer layers to make the plating current density and plating in the holes more uniform.
Meet the Author Podcast: Martyn Gaudion Unpacks the Secrets of High-Speed PCB Design
07/10/2025 | I-Connect007In this special Meet the Author episode of the On the Line with… podcast, Nolan Johnson sits down with Martyn Gaudion, signal integrity expert, managing director of Polar Instruments, and three-time author in I-Connect007’s popular The Printed Circuit Designer’s Guide to... series.
Showing Some Constraint: Design007 Magazine July 2025
07/10/2025 | I-Connect007 Editorial TeamA robust design constraint strategy balances dozens of electrical and manufacturing trade-offs. This month, we focus on design constraints—the requirements, challenges, and best practices for setting up the right constraint strategy.
Elementary, Mr. Watson: Rein in Your Design Constraints
07/10/2025 | John Watson -- Column: Elementary, Mr. WatsonI remember the long hours spent at the light table, carefully laying down black tape to shape each trace, cutting and aligning pads with surgical precision on sheets of Mylar. I often went home with nicks on my fingers from the X-Acto knives and bits of tape all over me. It was as much an art form as it was an engineering task—tactile and methodical, requiring the patience of a sculptor. A lot has changed in PCB design over the years.
TTCI Joins Printed Circuit Engineering Association to Strengthen Design-to-Test Collaboration and Workforce Development
07/09/2025 | The Test Connection Inc.The Test Connection Inc. (TTCI), a leading provider of electronic test and manufacturing solutions, is proud to announce its membership in the Printed Circuit Engineering Association (PCEA), further expanding the company’s efforts to support cross-functional collaboration, industry standards, and technical education in the printed circuit design and manufacturing community.