Overconstrain? Underconstrain? Selecting Materials for High-speed Designs
June 6, 2024 | Andy Shaughnessy, Design007 MagazineEstimated reading time: 1 minute
When selecting materials for a high-speed design, you need to be very familiar with the materials’ electrical characteristics, as well as the requirements of the PCB you’re designing. There are myriad details that need to be considered during the material selection process, and missing one iota can lead to your job being put on hold.
We asked Stephen Chavez, principal technical product marketing manager at Siemens, to share his thoughts on material selection for high-speed designs. Steph discusses material constraints, stackups, and the cut-off point when a “traditional” laminate will (and won’t) work for a high-speed board.
Andy Shaughnessy: What do designers need to keep in mind when selecting materials for a high-speed design?
Stephen Chavez: Regarding high-speed design, paying close attention to details is more critical than ever. This starts with dialing in and locking down a good foundation for the PCB, which is the stackup. The PCB stackup comprises the appropriate materials and structures to meet the design requirements and performance expectations. Locking in a good PCB stackup can be challenging, if not overwhelming when it comes to material selection.
Today, there exists a wide array of materials available for selection, encompassing diverse electrical, thermal, and other critical properties. Choosing the appropriate dielectric material hinges on the required frequency range and operational environment. As demands shift from conventional dielectric constants and thermal attributes (such as Tg and Td), there may be an associated increase in material costs as we move from standard materials to the more exotic materials. Materials boasting the lowest Dk and Df values tend to be pricier and may suffer from limited inventory availability, significantly impacting lead times. Where the Dk value is known as dielectric constant or relative permittivity, and the Df value is the dissipation factor or loss tangent, it tells a designer how lossy (electrical energy loss) a material may be. In simpler terms, it defines the ability of an insulator to store energy. It measures a material's ability to store electrical energy in an electric field. Additionally, when signal integrity and signal loss are critical, the micro-topography of copper foil cladding requires considerable attention. Numerous low-profile foils are available to mitigate and address signal loss.
To read this entire article, which appeared in the May 2024 Design007 Magazine, click here.
Suggested Items
The Critical Role of Materials
06/19/2024 | Marcy LaRont, PCB007 MagazineMaterials and substrates are an ongoing discussion for PCB fabricators today, offering PCB designers and fabricators much more choice than was available two decades ago. When it comes to running a printed circuit board company, material management is a critical piece for operations.
Standard of Excellence: Looking Five Years Into the Future
06/19/2024 | Anaya Vardya -- Column: Standard of ExcellenceThe future of the PCB industry will be based on technology. As components get smaller, denser, and more complicated, PCB fabrication companies must keep up with their customers’ needs both today and in the future. It is no longer enough to just keep up with our customers’ current needs. We must be prepared to meet their PCB needs three to five years out. We need a complete understanding of where our customers are going and what they will need in the near distant future.
Indium Corporation Expert to Present at High-Temperature Electronics Network Conference
06/18/2024 | Indium CorporationIndium Corporation Technical Manager for Europe, Africa, and the Middle East Karthik Vijay will deliver a technical presentation at the International Conference and Exhibition on High-Temperature Electronics Network (HiTEN 2024), taking place July 15-17 in Edinburgh, Scotland, United Kingdom.
Traditional Materials, High-Frequency Boards?
06/18/2024 | I-Connect007 Editorial TeamNot long ago, high-frequency and RF boards required specialized laminates, which tend to be costly and difficult to manufacture. But now, high-frequency designers use traditional PCB laminates for certain high-frequency boards. How is this possible? For some insight, we asked Ed Kelley, founder of Four Peaks Innovation and former CTO of Isola, to discuss how traditional materials have improved and what this means to PCB designers and design engineers today.
Marcy’s Musings: All Things Material
06/18/2024 | Marcy LaRont -- Column: Marcy's MusingsIt wasn’t until I had been around the business block a bit that I truly understood the impact of inventory on one’s P&L. How a company manages its inventory has a tremendous effect on its financials. I saw many situations where “fixers” were hired to get an organization financially back on track. The companies then experienced some of their greatest gains in the first year by simply getting their inventory under control. This is material management at its most base level for a business, and in this June issue of PCB007 Magazine, we are talking about all things “material,” a popular and ever-evolving topic for PCB fabricators.