Polar Instruments Launches New GRS200 with Extended Troubleshooting for the Repair of Electronic Assemblies
August 2, 2024 | Polar InstrumentsEstimated reading time: 1 minute
The new GRS200 fault locator from Polar Instruments uses the proven passive analogue signature analysis and compares a faultless assembly with the board under test. This method detects typical faults in electronics production, service and repairs quickly and without extensive circuit knowledge.
‘By using the GRS200, missing or reversed components, incorrect component values or component types, counterfeit components as well as short circuits or opens can be recognized very easily,’ says Hermann Reischer, Managing Director of Polar Instruments GmbH. The system consists of analogue signature hardware and powerful software with LIVE signature analysis, program mode and CAD data display. In addition, circuit diagrams, assembly photos, repair reports and an optional digital multimeter may be integrated. For detailed analysis, the system imports more than 20 different formats CAD data, including GenCAD, Hyperlynx, IPC-2581 and ODB++. Furthermore, circuit networks can be graphically highlighted and the associated components displayed.
The nodal impedance test is performed on the unpowered module, whereby a current-limited AC voltage signal generates an impedance signature by measuring voltage and current. The GRS200 system compares the signatures of the defective module with a stored good sample and indicates any noticeable deviations above a defined limit value. As an alternative to the nodal impedance test, an external multimeter can also be integrated into the test process. This allows, for example, voltage and resistance values, frequencies and temperatures to be assigned to defined test points in the CAD layout. It is also possible to locate short circuits on power supply rails and bus lines. An integrated short-circuit locator, in conjunction with the external multimeter, tracks the networks based on the CAD data using a highly sensitive four-wire resistance measurement and tone control. This makes it possible to narrow down the physical position of a short circuit to just a few millimeters.
Within the test program, test points are assigned to circuit networks in the CAD file and their analogue signatures are saved for later comparison. If no CAD data is available, test programs can also be created manually by defining the IC package style and the number of pins.
All test results are documented for traceability. Results for each assembly are recorded in a repair report, providing valuable repair history information. Using an optional USB camera, it is possible to take pictures of an assembly and save them as photo documentation in the test program.
Suggested Items
Cirexx International Inc. Chooses atg A9 Flying Probe Technology for High-speed Electrical Test
09/19/2024 | atg Luther & Maelzer GmbHatg Luther & Maelzer GmbH confirms delivery of high-speed bare board testing technology to PCB fabricator, Cirexx International Inc., in Santa Clara, CA.
Transtec and YAMAHA Motor Robotics to Showcase Latest Technology at SMTAI 2024
09/18/2024 | Yamaha Motor Robotics Holdings Co., Ltd.Trans-Tec America, in Partnership with Yamaha Robotics USA, will exhibit dynamic SMT assembly technologies at the SMTAI 2024 trade show and conference, October 20 - 24, 2024 at the Donald E. Stephens Convention Center in Rosemont, IL, USA.
TPY-4 Radar Completes Successful Risk Reduction Tests, 3DELRR program one step closer to battlefield success
09/17/2024 | Lockheed MartinThe U.S. Air Force Three-Dimensional Expeditionary Long Rang Radar (3DELRR) program team and Lockheed Martin successfully accomplished risk reduction testing for the TPY-4 radar. This event demonstrated the radar’s performance in a variety of conditions.
CentraTEQ Appointed as UK Distributor for MB Dynamics' Squeak & Rattle Test Systems
09/11/2024 | CentraTEQCentraTEQ, a leading UK supplier of Vibration Test Systems, proudly announces its new partnership as the exclusive UK distributor for German company MB Dynamics, renowned for their advanced buzz, squeak, and rattle (BSR) test systems.
NASA, Boeing Welcome Starliner Spacecraft to Earth, Close Mission
09/10/2024 | NASANASA and Boeing safely returned the uncrewed Starliner spacecraft following its landing at 10:01 p.m. MDT Sept. 6 at White Sands Space Harbor in New Mexico, concluding a three-month flight test to the International Space Station.