Dan’s Biz Bookshelf: The Ten Faces of Innovation
It’s Only Common Sense: Be the Solution, Not the Problem
American Made Advocacy: Long-time Challenges Confront a New Administration
DELO Releases IBOA-free Medical Adhesive for Glucose Monitoring Sensors and Other Wearables
March 14, 2025 | DELOEstimated reading time: 1 minute
DELO has released a new light-curing medical-grade adhesive engineered with nontoxicity in mind. DELO PHOTOBOND MG4047 is designed for wearable medical applications such as glucose monitoring sensors (CGM). Its chemical properties and impermeable characteristics help prevent skin irritation in cases of media influence such as rain or sweat.Teaser
With a 230-MPa Young’s modulus and a 200% elongation at tear while maintaining a 9-MPa compression shear strength, DELO PHOTOBOND MG4047 manages to be both a highly flexible and decidedly strong adhesive. These physical properties enable it to prevent common problems associated with wearable sensors such as sensor drift, which can occur following potting.
Chief among its advantages is that it is IBOA-free. IBOA, or isobornyl acrylate, is a chemical compound found in many polymer materials and is considered an extractable material. If medical wearables worn by patients are exposed to external media such as rain or sweat, tiny particles may leak out and contact the skin, causing adverse reactions such as irritation or allergies. Being free from IBOA reduces the risk of such reactions.
DELO PHOTOBOND MG4047 also demonstrates its nontoxicity through its biocompatibility, meeting the requirements outlined the DIN EN ISO 10993-5 cytotoxicity test. It complies with EU RoHS Directive 2015/863 as well, which is used to ensure nontoxicity in substances used in electronic equipment.
In addition to biocompatibility, DELO PHOTOBOND MG4047 achieves low water absorption at 0.15 wt%, resulting in low water permeation at 13 (g·mm)/(m²·24h). This creates a high water vapor barrier and prevents potential contact with other leachable substances.
The curing properties of this light-curing adhesive are optimized for mass medical wearable production with a required irradiation time of as little as two seconds under a 365–400-nm LED light with an intensity of 1000 mW/cm².
Share on:
Suggested Items
TI Introduces the World's Smallest MCU, Enabling Innovation in the Tiniest of Applications
03/12/2025 | PRNewswireTexas Instruments (TI) introduced the world's smallest MCU, expanding its comprehensive Arm® Cortex®-M0+ MSPM0 MCU portfolio. Measuring only 1.38mm2, about the size of a black pepper flake, the wafer chip-scale package (WCSP) for the MSPM0C1104 MCU enables designers to optimize board space in applications such as medical wearables and personal electronics, without compromising performance.
Yamaha Robotics Introduces 3 New Surface Mounter Innovations to Handle Special Requirements in Demanding Markets
02/26/2025 | Yamaha RoboticsYamaha Motor Corporation U.S.A. Robotics Division has introduced three hardware-based performance options for high-speed mounters that enhance productivity, quality control, and flexibility for handling special products such as large LED boards.
The Knowledge Base: Challenges and Considerations of Harsh Environments
02/26/2025 | Mike Konrad -- Column: The Knowledge BaseIn today’s rapidly advancing technological landscape, electronic assemblies are increasingly being deployed into environments that push their design and material limits. From the corrosive atmospheres of industrial facilities to the extreme temperatures and humidity of outdoor applications, harsh environments present a significant challenge to the reliability of electronic devices. This column explores the key issues impacting electronics reliability in such conditions, including electrochemical migration (ECM), corrosion, and the role of residue tolerance in assembly design.
Global Citizenship: Cultural Nuances Around the World
02/12/2025 | Tom Yang -- Column: Global CitizenshipBusinesses operate across diverse cultural landscapes, so it’s important to understand and embrace cultural nuances. Doing so facilitates smoother operations and can strengthen relationships and success in global markets.
Plasmatreat Korea to Exhibit at SEMICON Korea 2025
02/07/2025 | Plasmatreat KoreaPlasmatreat Korea, specialist in atmospheric pressure plasma technology for surface treatment, is pleased to announce its participation at SEMICON Korea 2025. From February 19 to 21, 2025, visitors will have the opportunity to learn more about Openair-Plasma and PlasmaPlus at booth P126 in the Platz Hall.