The Knowledge Base: The Era of Advanced Packaging
Standard of Excellence: Finding and Developing Future Leaders in Manufacturing
Global Sourcing Spotlight: Navigating the Variables of Holiday Schedules in Global Sourcing
ACE to Exhibit New Innovative Soldering Technologies at IPC APEX EXPO 2016
February 24, 2016 | ACE Production Technologies Inc.Estimated reading time: 1 minute
ACE Production Technologies Inc., a supplier of selective soldering systems, lead tinning systems and lead tinning services, will exhibit new innovative soldering technologies in Booth 2022 at the IPC APEX Expo, scheduled to take place March 15-17, 2016 at the Las Vegas Convention Center in Las Vegas, Nevada.
A complete range of standalone selective soldering systems including the popular KISS-102 and in-line systems such as the KISS-101IL, KISS-103IL and dual pot KISS-103ILDP will be on display. All systems are equipped with graphics-based software and include automatic fiducial correction and board warp compensation as standard features at no additional cost.
Premiering at APEX, is the LTS300-JEDEC which is the most technologically advanced molten solder lead tinning system on the market consisting of two dynamic nitrogen inerted solder pots, a dynamic flat wave fluxing station, forced convection preheating, aqueous wash and drying stations, plus a JEDEC tray stacker forming a complete component re-tinning work cell.
At the heart of the new LTS300-JEDEC is a fully integrated vision system consisting of top and bottom viewing cameras for accurate alignment of electronic components prior to re-tinning to ensure complete control over fine-pitch components during immersion and extraction of the hot solder dip process. The vision system also performs post-tinning inspection to detect potential solder bridges before placing components back into a JEDEC tray. The LTS300-JEDEC is a fully-configured system capable of performing a molten solder component lead tinning process for gold removal and re-tinning of components for Class 2 and Class 3 applications in compliance with the new J-STD-001, Rev F requirements.
Also on display will be the revolutionary STS-202 dip and look solderability test system. The new ACE solderability tester is capable of performing solderability testing to determine the solderability of component leads and terminations prior to being joined in a soldering operation. The system utilizes the proven dip and look test method in conformance with all IPC, ANSI and MIL standards including J-STD-002, MIL-STD-883 Method 2003 and MIL-STD-202 Method 208.
Share on:
Suggested Items
Book Excerpt: The Printed Circuit Assembler’s Guide to... Low-Temperature Soldering, Vol. 2, Chapter 5
12/23/2024 | I-Connect007 Editorial TeamChapter 5 introduces the advantages of using low-temperature soldering for through-hole components, including cost efficiency, reliability improvement, and reduced warpage. Also covered: the evaluation of different fluxes and the performance of HRL3 in wave soldering and selective soldering processes.
Overview of Soldering Systems With Vacuum
12/18/2024 | Dr. Paul Wild, Rehm Thermal Systems GmbHWhen soldering electronic assemblies, the focus of the vacuum application is on the removal of volatile substances from the solder joints and the associated reduction of pore formation. Particularly in the thermal management of power electronics components, pores can cause so-called hotspots with higher temperatures due to their poor heat conduction. These hotspots can lead to overheating of the components on the one hand and to thermally induced destruction of the solder structure on the other.
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
12/13/2024 | Andy Shaughnessy, I-Connect007This week, Peter Tranitz discusses the upcoming Pan-European Electronics Design Conference, set for Jan. 29-30 in Vienna, Austria. Pete Starkey brings us a review of the most recent EIPC Technical Snapshot webinar, which featured a global PCB maker update by Dr. Hayao Nakahara. Don't miss our interview with Manfred Huschka, who explains how companies can begin their own China Plus One plan. Stan Farnsworth breaks down photonic soldering and discusses its use in soldering materials that are not typically compatible. I also enjoyed Dan Beaulieu’s discussion on the value of consistency, and why just showing up for work is half the battle, especially in an inconsistent, evolving industry like ours.
Advancing Photonic Soldering
12/11/2024 | Nolan Johnson, SMT007 MagazineStan Farnsworth, director of customer satisfaction at PulseForge, discusses the advancements in photonic soldering that highlight its energy efficiency and versatility. Over the past two years, the company has refined its applications for flexible substrates and energy reduction, finding that photonic soldering allows the processing of materials that typically aren’t thermally compatible and offers significant energy savings compared to traditional methods.
Indium Introduces New ROL0 and Halogen-free Flux-cored Wire
12/11/2024 | Indium CorporationIndium Corporation announced the global availability of CW-807RS, a new high-reliability, halide- and halogen-free flux-cored wire that improves wetting speeds and cycle times for electronics assembly and robot soldering applications.