All About Flex: Considerations for Impedance Control in Flexible Circuits
August 4, 2016 | Dave Becker, All FlexEstimated reading time: 4 minutes

Impedance can be thought of as a system’s opposition to alternating or pulsing electronic current. The unit of measurement is ohms, the same unit of measurement in a direct current system. However, the components for calculating impedance are much more complex than DC resistance. For a direct current system, the resistance is related to the relative ease with which electrons can flow through the material. Ohm’s law describes a fairly straightforward relationship between current and voltage (V=IR or R=V/I) where R is a constant number for any given material. Impedance is characterized by the equation including the DC resistance but also includes another component called reactance. Reactance is the ability of the system to store and release energy as current or voltage alternates. The equation for impedance is Z=R +iX, where iX is the reactance component. The reactance is a function of the capacitance of the system and the frequency of the alternating or pulsing current.
Why is impedance important?
Impedance is important for high-speed electronics. When frequencies become 200 MHz or higher, the impedance and impedance consistency becomes a significant factor in the system performance. During the last 20 years, electronic packages have become smaller, denser and faster. It is estimated that in 2000, only a small percentage of PCB and flexible printed circuit (FPCB) designs had an impedance requirement. As higher and higher frequencies continue their relentless march, impedance requirements today have become much more prevalent and important.
In a direct current system, when two components of different resistance are connected in series, the system resistance is simply equal to the two components added together (R1 +R2). The flow of the electrons is homogenous. The analogy is a garden hose where the flow of the water is the same throughout the hose.
In high-speed electronics, impedance does NOT behave the same way. High speed signals are like separate pulses propagating through the system. The current and magnetic pulses are affected by the impedance. When the pulses encounter a node of mismatched impedance, a flux of energy is induced which creates competing signals that can interfere with the main signal. The result is power loss and distortion of the signal.
Many nodes of mismatched impedance can occur within a PCB system as attached components, conductor width, conductor spacing and dielectric thicknesses change. One way to deal with this issue is to isolate the signal traces so that the dielectric and geometries are identical throughout the signal path. This is called controlled impedance. In flexible circuits, there are two categories of designs that are typically used for controlled impedance: microstrip and stripline (Figure 1). Within the categories one can have single-ended transmission lines and differential pair transmission lines.
Figure 1: Designs for controlled impedance.
In both designs, the impedance is affected by the following:
- Dielectric constant (Dk) of the materials
- The DC resistance of the signal line
- Distance between the signal lines and ground planes or signal line pairs
Page 1 of 2
Suggested Items
The Evolution of Picosecond Laser Drilling
06/19/2025 | Marcy LaRont, PCB007 MagazineIs it hard to imagine a single laser pulse reduced not only from nanoseconds to picoseconds in its pulse duration, but even to femtoseconds? Well, buckle up because it seems we are there. In this interview, Dr. Stefan Rung, technical director of laser machines at Schmoll Maschinen GmbH, traces the technology trajectory of the laser drill from the CO2 laser to cutting-edge picosecond and hybrid laser drilling systems, highlighting the benefits and limitations of each method, and demonstrating how laser innovations are shaping the future of PCB fabrication.
Day 2: More Cutting-edge Insights at the EIPC Summer Conference
06/18/2025 | Pete Starkey, I-Connect007The European Institute for the PCB Community (EIPC) summer conference took place this year in Edinburgh, Scotland, June 3-4. This is the third of three articles on the conference. The other two cover Day 1’s sessions and the opening keynote speech. Below is a recap of the second day’s sessions.
Day 1: Cutting Edge Insights at the EIPC Summer Conference
06/17/2025 | Pete Starkey, I-Connect007The European Institute for the PCB Community (EIPC) Summer Conference took place this year in Edinburgh, Scotland, June 3-4. This is the second of three articles on the conference. The other two cover the keynote speeches and Day 2 of the technical conference. Below is a recap of the first day’s sessions.
Preventing Surface Prep Defects and Ensuring Reliability
06/10/2025 | Marcy LaRont, PCB007 MagazineIn printed circuit board (PCB) fabrication, surface preparation is a critical process that ensures strong adhesion, reliable plating, and long-term product performance. Without proper surface treatment, manufacturers may encounter defects such as delamination, poor solder mask adhesion, and plating failures. This article examines key surface preparation techniques, common defects resulting from improper processes, and real-world case studies that illustrate best practices.
RF PCB Design Tips and Tricks
05/08/2025 | Cherie Litson, EPTAC MIT CID/CID+There are many great books, videos, and information online about designing PCBs for RF circuits. A few of my favorite RF sources are Hans Rosenberg, Stephen Chavez, and Rick Hartley, but there are many more. These PCB design engineers have a very good perspective on what it takes to take an RF design from schematic concept to PCB layout.