Understanding MIL-PRF-31032, Part 4
October 20, 2020 | Anaya Vardya, American Standard CircuitsEstimated reading time: 3 minutes
![](https://iconnect007.com/application/files/3716/3121/8862/Anaya_Vardya-200.jpg)
Overview
Continuing with Part 4 of the discussion on understanding the military PCB performance standard MIL-PRF-31032, the next step in the process is to create four new procedures to address the unique requirements of the military.
Qualification and Add-On Procedure
This process provides the guidelines for the initial qualification of the company, as well as a path for future add-on qualifications. The first thing that needs to be included is the process for developing the qualification test vehicle. This is the specific PCB design that will be used to build the qualification boards. The documentation required must also be identified, such as production traveler, test vehicle design, drawings, multilayer layup, etc.
Test Vehicle
A company will qualify for specific technology and will need to develop a qualification test plan, which is a document that specifies the following minimum attributes of the qualification board:
- Max. Number of Layers and Dielectric Type
- Max. Panel Size
- Max. Board Thickness
- Min. Drilled Hole Before Plating
- Aspect Ratio
- Min. Conductor Width
- Via Structure
- Min. Conductor Space
- Hole Preparation
- Hole Wall Conductive Coating
- Copper Plating
- Solder Resist
- Silkscreen
- Final Finish
- Additional Fabrication Capabilities
- Controlled Impedance
It is important to note here that the qualification “flows down” but not “up.” In other words, if an 18-layer is qualified, layer counts less than 18 layers can be built as long as the other above parameters are the same, but a 20-layer would not be allowed.
Sample Size and Data Requirements
The next section would be to establish the lot size of the qualification lot and the sample sizes that will be used for testing. The data recording and retention of all qualification records must be defined, including coupons and any extra boards left over from the qualification lot.
Failure Analysis and Resubmission
A DLA-approved third-party testing lab must be selected to use for the initial qualification as well as the ongoing monthly testing. Should a submitted sample fail any tests, this procedure needs to have a provision for failure analysis and corrective action. This typically leverages the existing processes already in place. The rules for resubmitting new qualification boards must also be defined here, particularly that additional extra samples from the failed lot cannot be used.
Qualification Test Summary and Reporting
This section outlines the components for the summary that is needed to be submitted to the DLA after all tests and inspections have been successfully performed, including the third-party lab). This includes things like the travelers, internal and external test and inspection results, lot conformance forms and results, failure mode for any rejections, dimensional and electrical test parameters and measurements, and a copy of the qualification test plan.
Add-On Qualification
MIL-PRF-31032 allows for the expansion of the qualified technology through the add-on qualification process. A technology that falls within 25% of the current qualified technology can be built with a new qualification test plan and TRB approval. For example, with a qualified 18-layer, a 22-layer could be qualified through the add-on process.
The same would apply to line width, hole size, etc. There is no need to wait for DLA approval in these cases; they will verify the add-on qualification data during their next regular visit/audit. Anything greater than a 25% technology change will require a new full qualification like the initial qualification.
Conclusion
This wraps up qualification and add-on procedures. Part 5 will focus on the next unique procedure needed to produce MIL-PRF-31032 PCBs.
Editor’s note: Read Part 1, Part 2, and Part 3.
Anaya Vardya is president and CEO of American Standard Circuits; co-author of The Printed Circuit Designer’s Guide to… Fundamentals of RF/Microwave PCBs and Flex and Rigid-Flex Fundamentals; and author of Thermal Management: A Fabricator's Perspective. Visit I-007eBooks.com to download these and other free, educational titles. He also co-authored “Fundamentals of PCB Technology.”
Suggested Items
Eutect Overcomes Panel Soldering Challenges with New Gripper
09/06/2024 | Eutect GmbHThe selective soldering of assemblies in panels is not a real challenge. However, if you need to solder relatively large panels with towering components, specialists like those at Eutect GmbH have to step up to the plate.
AIM Solder Appoints Kevin Kwan as Business Development Manager in Asia
09/06/2024 | AIM SolderAIM Solder, a global leader in solder assembly materials for the electronics industry, is thrilled to announce the appointment of Kevin Kwan as Business Development Manager for the Asian market.
Solder Printing: A 1:1 Ratio of Technical and Creative
09/03/2024 | Nolan Johnson -- Column: Nolan's NotesWhen things get technical, I’m in my happy place. It’s why I work in technology in the first place. I also happen to enjoy creative pursuits, and my real happy place is when both happen at the same time. Over the years, it seems that most of us engaged in printed circuit design and manufacturing are similarly wired. I don’t think I’m alone in stating that finding a creative solution to a technical problem is one of the highlights of our workday. We get bonus points if the solution is particularly simple or uncomplicated.
AIM to Present on Ultra-Miniature Assembly for Mini/MicroLEDs at MicroLED Connect
09/03/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce its participation in the upcoming MicroLED Connect Conference and Exhibition taking place September 25-26 in the Conference Center at High Tech Campus Eindhoven in The Netherlands.
STARTEAM GLOBAL Announces Strategic Partnerships with Notion Systems and Peters Group
09/03/2024 | STARTEAM GLOBALSTARTEAM GLOBAL, an established printed circuit board (PCB) manufacturer with over 35 years of expertise, is pleased to announce new strategic partnerships with two German corporations: Notion Systems GmbH, a manufacturer of inkjet printing systems for functional materials, and Lackwerke Peters GmbH & Co. KG, also known as Peters Group, a full-range supplier of coating materials for electronics and PCBs worldwide.