-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueWet Process Control
In this issue, we examine wet processes and how to obtain a better degree of control that allows usable data to guide our decisions and produce consistently higher-quality products.
Don’t Just Survive, Thrive
If we are to be relevant and prosper during these next critical decades in electronics, we must do more than survive. As an industry, we can and must thrive. In this issue, our contributors explore these concepts meant to help you take your business to the next level.
Material Matters
Materials management is nuanced, multifaceted, and requires a holistic systems approach for business success. When building high mix, low volume, and high technology, managing materials and overall cost containment are even greater challenges.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - pcb007 Magazine
ECWC15 Virtual Conference Keynote: 5G PCB Technology and Material Challenges
December 7, 2020 | Pete Starkey, I-Connect007Estimated reading time: 7 minutes
![](https://iconnect007.com/application/files/3616/3116/1066/pete-starkey-300.jpg)
The second day of the Electronic Circuits World Convention began with a keynote from Dr. Shiuh-Kao Chiang, managing partner of Prismark, describing the PCB technology and material challenges presented by the introduction of the fifth-generation cellular wireless communication network—the roll-out of which was continuing in spite of the coronavirus pandemic.
The electronics industry was in the midst of a period of radical change, the main stimulus being a fundamental upgrade in infrastructure equipment, with printed circuits driven by high-speed, high-frequency demands to enable much faster wireless communication. Once the data-centre investment cycle and 5G build-out had been completed, momentum was likely to shift back to smart and portable consumer products. Dr. Chiang forecast that for the next few years, the industry would continue to grow at a compound rate of over 5%.
From a product perspective, while other sectors were suffering a decline in value, packaging substrates were showing relatively strong growth due to demand for components used in computer-related areas: central processor units, graphics processor units, artificial intelligence, and advanced packaging for large devices. For the next few years, continuing growth was forecast in packaging substrates, high-density interconnect, flexible circuits, and multilayer boards.
Multilayer boards would continue to play a very important role in 5G infrastructure, servers, and networking systems, but their material characteristics and fabrication techniques required improvement in order to satisfy the high-speed demand. Developments in HDI and flex would be driven by portable systems and substrate developments by flip-chip BGA and 5G terminal devices, particularly the antenna-in-package (AIP) module used in the 5G smartphone. Dr. Chiang considered the industry to be in the middle of the infrastructure transformation, and that 5G was the key element of that change.
The most important feature of the infrastructure upgrade was that the signal was travelling at a much higher speed and at a much higher frequency. “High speed in the board, high frequency in the air.” This applied to almost all the devices and presented challenges to the PCB industry: to develop newer technology, newer materials, and newer processing methods to avoid signal loss and ensure that data could be transmitted at a higher rate without suffering distortion or interference.
Major features differentiating 5G from its 3G and 4G predecessors were high frequency and multiple-in-multiple-out (MIMO), necessitating multiple antennae capable of changing and strengthening the signal in certain directions. The design of the circuit board in the base station required multiple antenna elements and the ability to receive, process, and transmit signals at high frequency. And the terminal device—for example, a mobile phone—is similarly required to receive and transmit signals at high frequency, making the PCB more complex (and of substantially higher value) than its 4G equivalent. Additionally, high-value flexible circuits and feed-lines would be required, fabricated from materials capable of carrying high-frequency signal without distortion or loss. Advanced low-loss rigid and flexible materials presented challenges to laminate suppliers.
But the 5G system involved much more than high-frequency communication between the terminal device and the base station: the networking system passed the signal to the data centre, server, data processing, data storage, or data re-direct to other users. The overall system was bringing major changes to the architecture of the base station. In the past, the antenna, the power amplifier, and the transceiver were typically separate functional units, with the antenna at the top of the tower and the other units in the base station. Alternatively, everything but the base-band unit could be incorporated in the tower box, together with the antenna.
Dr. Chiang made it clear that the material challenge of a 5G system depended on the frequency range it was operating in and which functional unit of which circuit board was being considered. 5G could effectively be seen as two different systems: less than 6 GHz was classed as “mid-to-low frequency,” and millimetre-wave as “high-frequency.” In the mid-to-low frequency class, the architecture was actually similar to that of the 4G base station, the main difference being that more antenna units were required, but the frequency band was actually similar to 4G, and the industry had plenty of experience in designing, manufacturing, and assembling PCBs for this frequency range. The main trend involved the integration of a transceiver, power amplifier, and antenna together as an active antenna.
In contrast, 5G operating at frequencies of up to 70 GHz required new materials—typically high-frequency material for the antenna and high-speed material for the base-band unit. Many different low-loss materials had been introduced over the past 2–3 years, some PTFE-based, some modified PTFE-like material, with low Dk and low Df characteristics, which were processable and suitable for the integration of the antenna function, the power amplifier function the transmit-receiver function into one active antenna unit. Fine-pitch circuitry and HDI were typical design features, with high layer count and high component density.
An active antenna unit for a 5G base station had multiple antenna elements, individually small in size because they were handling shorter wavelengths, and all mounted on a main board to reduce cable losses. Transceiver components were placed on the reverse of the main board, together with other active and passive components to complete the active antenna function. This type of integration was becoming common, not only in 5G base stations but also linked to other communication equipment and processors, storage, and servers because of the rapid escalation of data generated by consumers.
As wireless communication transferred to the 5G standard, wired communication for computing and processing equipment was also moving to a new standard to enable higher data rates and volumes. Advances in data transfer standard from PCIe 3.0 to PCIe 4.0 to PCIe 5.0 demanded laminate to be upgraded from mid-loss to low-loss to very-low-loss, and the industry was presently in the middle of this transition process. Similarly, with the networking system, changing standards necessitated a move from very-low-loss to ultra-low loss laminates with lower Dk and lower Df. Typically, materials were grouped into two categories: high-speed, which is usually used for server, base station, and base-band units—and RF—high-frequency, low-loss material, which is usually used for the antenna function. The two groups were merging together for ultra-low-loss, with dielectric properties approaching those of an RF material.
In general, material properties continued to improve and satisfy the need for higher-frequency and higher-speed applications. And in developments beyond ultra-low-loss, materials with even lower Dk and Df values were becoming commercially available. Not only were base station considerations creating material challenges, but 5G terminal devices also had specific requirements.
Dr. Chiang’s team had examined the workings of the newly-released iPhone 12 with the 5G millimetre-wave feature. For frequencies under 6 GHz, the antenna structure was typically similar to that used in 4G. But separate antennae were needed for high-frequency 5G signals, and the iPhone 12 had three separate antennae: passive units facing to the front and back and an antenna-in-package module facing to the side with different structures for different frequencies. The passive antennae were connected to active components elsewhere on the main board. The antenna-in-package module incorporated transceiver and passive components to form a complete antenna function. A cross-section of this module showed a very sophisticated 16-layer any-layer circuit board in low-loss material, with its component side facing inward and the antenna part facing out.
Two of the antennae were connected to the main board through feed-lines, flexible circuits made of very-low-loss material, similar to the PTFE-like antenna circuit board used in the 5G base station—an example of a new material specially developed for 5G applications. Liquid crystal polymer has become popular as a low-loss flexible circuit material.
Although low Dk and low Df values could be achieved by modifying resin formulations and additives, low Dk glass fabric could further improve dielectric properties, although the cost was high and supply was limited. Signal integrity could be improved and transmission losses through skin effect reduced by the use of low-profile copper foil, and Dr. Chiang showed a comparison of different foil grades from general purpose to the ultra-smooth H-VLP2 material compatible with millimetre-wave frequencies. Reverse-treated foil was also available.
Dr. Chiang’s keynote presentation was a detailed and comprehensive overview of the changing electronics industry and the challenges being overcome by material suppliers and PCB fabricators in meeting the technological demands of 5G as it continues its evolution.
This was an informative, stimulating, and enjoyable introduction to the second day of the ECWC15 Virtual Conference. My grateful thanks to the Hong Kong Printed Circuit Association for hosting and managing a superb event.
Suggested Items
Atotech to Participate at KPCA Show 2024
09/03/2024 | AtotechMKS’ Atotech will participate in this year’s KPCA Show 2024 in Incheon, held at Songdo Convensia from September 4-6, 2024.
Victory Announces Breakthrough in PCB Technology with New Product Launch
08/29/2024 | openPRShenzhen Victory Electronics Technology Co., Ltd., a leader in the printed circuit board (PCB) manufacturing industry, is proud to announce the successful development of a groundbreaking new product.
Connect the Dots: Designing for Reality—Electroless Copper
08/28/2024 | Matt Stevenson -- Column: Connect the DotsRoll up your sleeves because it's time to get messy. In a recent episode of I-Connect007’s On the Line with… podcast, we discussed electroless copper deposition. This process deposits a copper layer into the through-holes and vias of what will eventually be a PCB. Electroless copper deposition feels like a black box to many people. It sort of looks like a black box, too. The boards go in one side, come out the other, and emerge differently. So, let's crack open that black box and look inside.
Maximizing ROI Through Better Wet Process Control
08/20/2024 | I-Connect007 Editorial Team“When things get out of control, the variation in your wet process begins,” says Mike Carano,. “Just because they look like good boards and may even pass electrical test, it does not necessarily mean you have good boards. Once the chemistry is headed toward the right or left side of the process control parameter cliff, the plating is compromised. If the copper is thinner than it should be, when the customer puts it into service, the board may fail after 500 cycles vs. the requisite 1,000 or 2,000 cycles. The root cause issue is that you plated 7/10ths of a mil of copper instead of one-mil of copper because you were not controlling your process. The fact that you passed your own electric test becomes inconsequential.”
The Chemical Connection: Controlling an Alkaline Etch Bath With Low Copper Loading
08/07/2024 | Don Ball -- Column: The Chemical ConnectionThis month, I wanted to continue my discussion on how much process control is actually needed for high-density circuit production. However, in the last month, I have been called on to help with a specific process control problem: how to control an alkaline etch bath when you’re not etching much copper. This problem has been cropping up more frequently as smaller shops (and a few larger ones) concentrate on low-volume, high-value plated through-hole panels such as prototypes, resistor cores, etc.