-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueThe Hole Truth: Via Integrity in an HDI World
From the drilled hole to registration across multiple sequential lamination cycles, to the quality of your copper plating, via reliability in an HDI world is becoming an ever-greater challenge. This month we look at “The Hole Truth,” from creating the “perfect” via to how you can assure via quality and reliability, the first time, every time.
In Pursuit of Perfection: Defect Reduction
For bare PCB board fabrication, defect reduction is a critical aspect of a company's bottom line profitability. In this issue, we examine how imaging, etching, and plating processes can provide information and insight into reducing defects and increasing yields.
Voices of the Industry
We take the pulse of the PCB industry by sharing insights from leading fabricators and suppliers in this month's issue. We've gathered their thoughts on the new U.S. administration, spending, the war in Ukraine, and their most pressing needs. It’s an eye-opening and enlightening look behind the curtain.
- Articles
- Columns
- Links
- Media kit
||| MENU - pcb007 Magazine
Calumet is Bullish on Additive and Semi-Additive
March 15, 2022 | I-Connect007 Editorial TeamEstimated reading time: 3 minutes

Calumet Electronics has been a domestic pioneer with additive and semi-additive electronics manufacturing processes. We recently asked Calumet’s Todd Brassard and Meredith LaBeau to discuss the state of this technology, which traditional processes that they might replace, and some of the challenges facing OEMs or PCB shops that are considering these options.
Barry Matties: We’re seeing more additive and semi-additive. Let’s start with what these technologies represent to Calumet.
Todd Brassard: I’m sure some of your readers will go a little crazy at our use of the word “additive.” In my mind, pure “additive” manufacturing is 3D-printed or deposition-based processes while “semi-additive,” in the context of circuit board substrates, involves a seed layer of copper (A-SAP™) or a very thin layer of copper foil (mSAP) with plated copper traces and features.
We understand the distinctions between terms additive and semi-additive; we do not use “additive” to necessarily describe a process, but rather as a proper noun to name the thing and contrast it against “subtractive” processes. For example, when working with Averatek’s A-SAP™ technology, the seed layer is so thin that it is removed with a simple micro-etch. To me, the process is so close to being purely additive, I name it an additive process.
Matties: Is it going to be a mandatory offering for most fabricators in the coming years? Or is this something that will still be limited in scope?
Meredith LaBeau: What is driving the need for additive manufacturing—and I use this term “additive” as Todd just described—is design size and complexity. Next generation electronics will be much smaller. This is easy to see just following the mobile device industry. An electronic interconnect manufacturer in the U.S. can only go so small with traditional subtractive manufacturing processes.
Another piece of this push toward additive technology is environmental. There will be many more conversations about the environmental impact of manufacturing processes, and these considerations will factor more heavily into contract awards. With traditional subtractive processes you’re removing copper, but with additive processes you’re mostly adding copper. I believe there's going to be a shift in design to reduce waste streams regardless of technology, as part of the wider ESG movement.
Todd Brassard: Yes, ESG: environmental and social governance.
Matties: Is that becoming more prevalent?
LaBeau: We are just starting to see environmental considerations seep into conversations and design considerations at our level.
Todd Brassard: We are seeing more environmental considerations flowing down from the DoD. The DoD wants to see transition to greener solutions. Calumet is learning the ropes of federal funding and we believe environmental considerations must be included in any submitted proposal. We’ve been seeing these types of requirements added to RFPs in the last few years. Personally, I believe this is a good thing. We should be paying attention to what we are doing to the planet; this is just common sense.
LaBeau: The additive and semi-additive movements are not just about miniaturization, but also system performance and integrity. Additive and semi-additive technologies provide for better copper trace and feature formation which improves signal integrity and shortens transmission lines, allowing faster bit rates and higher frequencies. For example, radar and communications systems achieve higher performance when trace walls are square and smooth. Combine the potential for feature formation with advanced materials and chemical processes and a wide array of possibilities emerge. As an example, Calumet can plate copper on transparent substrates; just imagine the applications, for example, in the augmented reality space.
To read this entire conversation, which appeared in the February 2022 issue of PCB007 Magazine, click here.
Suggested Items
Trump Copper Tariffs Spark Concern
07/10/2025 | I-Connect007 Editorial TeamPresident Donald Trump stated on July 8 that he plans to impose a 50% tariff on copper imports, sparking concern in a global industry whose output is critical to electric vehicles, military hardware, semiconductors, and a wide range of consumer goods. According to Yahoo Finance, copper futures climbed over 2% following tariff confirmation.
Happy’s Tech Talk #40: Factors in PTH Reliability—Hole Voids
07/09/2025 | Happy Holden -- Column: Happy’s Tech TalkWhen we consider via reliability, the major contributing factors are typically processing deviations. These can be subtle and not always visible. One particularly insightful column was by Mike Carano, “Causes of Plating Voids, Pre-electroless Copper,” where he outlined some of the possible causes of hole defects for both plated through-hole (PTH) and blind vias.
Trouble in Your Tank: Can You Drill the Perfect Hole?
07/07/2025 | Michael Carano -- Column: Trouble in Your TankIn the movie “Friday Night Lights,” the head football coach (played by Billy Bob Thornton) addresses his high school football team on a hot day in August in West Texas. He asks his players one question: “Can you be perfect?” That is an interesting question, in football and the printed circuit board fabrication world, where being perfect is somewhat elusive. When it comes to mechanical drilling and via formation, can you drill the perfect hole time after time?
The Evolution of Picosecond Laser Drilling
06/19/2025 | Marcy LaRont, PCB007 MagazineIs it hard to imagine a single laser pulse reduced not only from nanoseconds to picoseconds in its pulse duration, but even to femtoseconds? Well, buckle up because it seems we are there. In this interview, Dr. Stefan Rung, technical director of laser machines at Schmoll Maschinen GmbH, traces the technology trajectory of the laser drill from the CO2 laser to cutting-edge picosecond and hybrid laser drilling systems, highlighting the benefits and limitations of each method, and demonstrating how laser innovations are shaping the future of PCB fabrication.
Day 2: More Cutting-edge Insights at the EIPC Summer Conference
06/18/2025 | Pete Starkey, I-Connect007The European Institute for the PCB Community (EIPC) summer conference took place this year in Edinburgh, Scotland, June 3-4. This is the third of three articles on the conference. The other two cover Day 1’s sessions and the opening keynote speech. Below is a recap of the second day’s sessions.