Knocking Down the Bone Pile: Addressing End-of-life Component Solderability Issues, Part 4
Nolan’s Notes: Finding Your Sweet Spot
Standard of Excellence: Delivering Excellence—A Daily Goal
Book Excerpt: 'The Printed Circuit Assembler’s Guide to… Solder Defects'
June 7, 2022 | I-Connect007 Editorial TeamEstimated reading time: 1 minute
The Printed Circuit Assembler’s Guide to… Solder Defects—authored by the experts at Indium Corporation and exclusively available in the I-007eBook library—is specifically dedicated to educating the printed circuit board assembly sector and serves as a valuable resource for people seeking the most relevant information available. What follows is the introduction from this book.
Introduction:
In 2006, much of the world switched from tin-lead to lead-free solder. The European Union’s Restriction of Hazardous Substances (RoHS) directive, which essentially eliminated lead from electrical solder, drove this global move. This change has challenged circuit board assemblers since Pb-free solders melt at temperatures nearly 40°C hotter than lead-containing solders, and they do not flow or wet as well as SnPb solders.
At the same time, the density of electronics has unabatedly increased. This density increase has resulted in exponentially more powerful electronics—the fastest supercomputer of 1996 is outperformed by today’s iPhone 11 Pro—creating another challenge for assemblers. Whereas the 0402 passive was the leading edge in miniaturization in the SnPb era, the 0201, 01005, and smaller passives have emerged for Pb-free soldering. The combined challenges of Pb-free soldering and ever-increasing miniaturization have resulted in new or exacerbated defects in electronics assembly. This book was developed to address this problem, and will address the following defect topics:
- Voiding in SMT Assembly
- Graping
- Head-in-Pillow and Non-Wet Open Defects
- Tombstoning of Passive Components
- Solder Paste Insufficients
- Solder Balling and Beading
It is also important to recognize that effective electronics assembly is an optimization process—often, minimizing one defect will exacerbate another. So, in addition to the information presented here, when confronted with a process defect or challenge, it is helpful to refer to experts from your materials or equipment suppliers. IPC and SMTA standards should provide further guidance as well, along with the many excellent courses presented by these industry organizations.
Share on:
Suggested Items
Knocking Down the Bone Pile: Addressing End-of-life Component Solderability Issues, Part 4
07/15/2025 | Nash Bell -- Column: Knocking Down the Bone PileIn 1983, the Department of Defense identified that over 40% of military electronic system failures in the field were electrical, with approximately 50% attributed to poor solder connections. Investigations revealed that plated finishes, typically nickel or tin, were porous and non-intermetallic.
SHENMAO Strengthens Semiconductor Capabilities with Acquisition of PMTC
07/10/2025 | SHENMAOSHENMAO America, Inc. has announced the acquisition of Profound Material Technology Co., Ltd. (PMTC), a premier Taiwan-based manufacturer of high-performance solder balls for semiconductor packaging.
KYZEN to Highlight Understencil and PCB Cleaners at SMTA Querétaro Expo and Tech Forum
07/09/2025 | KYZEN'KYZEN, the global leader in innovative environmentally responsible cleaning chemistries, will exhibit at the SMTA Querétaro Expo & Tech Forum, scheduled to take place Thursday, July 24, at Centro de Congresos y Teatro Metropolitano de Querétaro.
Driving Innovation: Direct Imaging vs. Conventional Exposure
07/01/2025 | Simon Khesin -- Column: Driving InnovationMy first camera used Kodak film. I even experimented with developing photos in the bathroom, though I usually dropped the film off at a Kodak center and received the prints two weeks later, only to discover that some images were out of focus or poorly framed. Today, every smartphone contains a high-quality camera capable of producing stunning images instantly.
Hands-On Demos Now Available for Apollo Seiko’s EF and AF Selective Soldering Lines
06/30/2025 | Apollo SeikoApollo Seiko, a leading innovator in soldering technology, is excited to spotlight its expanded lineup of EF and AF Series Selective Soldering Systems, now available for live demonstrations in its newly dedicated demo room.