-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueWet Process Control
In this issue, we examine wet processes and how to obtain a better degree of control that allows usable data to guide our decisions and produce consistently higher-quality products.
Don’t Just Survive, Thrive
If we are to be relevant and prosper during these next critical decades in electronics, we must do more than survive. As an industry, we can and must thrive. In this issue, our contributors explore these concepts meant to help you take your business to the next level.
Material Matters
Materials management is nuanced, multifaceted, and requires a holistic systems approach for business success. When building high mix, low volume, and high technology, managing materials and overall cost containment are even greater challenges.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - pcb007 Magazine
A Focus on Process Control, Part 1
September 27, 2022 | I-Connect007 Editorial TeamEstimated reading time: 7 minutes
![](https://iconnect007.com/application/files/6916/9086/9445/Mike_Carano_Averatek.jpg)
Michael Carano is a noted subject matter expert with respect to process control, electroplating and metallization technology, surface finishing, and reliability. So, it was only natural that we sat down to talk about mechanizing an existing facility given today’s fickle environment. Will any of the CHIPS funding trickle down to bare board fabrication? What process can be adjusted on the factory floor? The focus needs to be more than just on manufacturing and getting work out the door, he says, but also process control.
Nolan Johnson: You have a wide-ranging view of the current market, and how fabricators should approach advancing their capabilities. Walk us through your IPC Thought Leaders Program paper.
Michael Carano: To start, everyone is talking about the $52 billion CHIPS Act, but our folks in the PCB industry say, “Hey, that’s great, but chips don’t float. Where are the chips going to go?” Unless we build out PCB capacity as well, the chips will “float back” over the ocean into an OSAT or something like that. There’s no IC substrate capability here with any volume.
In my paper, I was asking about what it would take to double the capacity of existing fabrication by upgrading the equipment. It would be about $10 to $12 million per fabricator, with maybe 100 fabricators altogether—about $1.2 billion. Now if you include brick and mortar, then I would double that number to about $3.5 billion, then double again to a $7 billion market over a couple of years by making this investment, whether it comes from government, in-kind states, or whatever.
Upgrading of the opportunities would include horizontal equipment, new plating technologies, reliability, testing internally, materials handling, via formation, laser drilling, and more. I looked at all new equipment, state-of-the-art flying probe testing. That’s all included.
Now, if you just started with the greenfield, that might be more like a $25 to $40 million investment. But take our key five or six fabricators out there—such as TTM, Summit, APCT, FTG, Calumet—that have several fabrication sites under their ownership. They have quality people and engineering. If the DoD really wants to have some safety and security, then we need some help. There’s a way to do it that doesn’t even put a dent into that $52 billion.
Johnson: For the CHIPS Act, it’s about 2% of the funding.
Carano: Exactly. Let’s use that to get into the technology and what it will take to make this work. Our fabricators are capable and stable. They’re well managed, but in making that investment, they need some help to minimize or de-risk some of the investment they would have to make. I know they could do it and do it well.
The chemical processes keep evolving, materials keep getting better. When some say, “Look at what’s going on in Asia, the chemistry works so well.” Wait a minute, it’s the same chemistry, so it’s nothing secret; 90% of the chemistry in the world and materials were developed by U.S.-based companies. They may have facilities all over the world, but that technology is there. When someone tells me the plating technology doesn’t exist here, that’s not true.
Digital Factory
Barry Matties: Where does the digital factory come into your thinking for bare board fabricators? There seems to be a lot of reluctance, a “we’re small and that doesn’t work for us” mentality.
Carano: You hear about CFX and the Factory of the Future. The assembly companies see the machines, the need for them to be interconnected, how the data is transferred, basic monitoring, and even if there’s a glitch, how it can be repaired quickly.
Then there’s blockchain. What will that do for me? This is a big part of the security of any transaction, software development, or factory operation. They don’t see the connection, or the cost seems to be a concern. Furthermore, why aren’t we investing in more semi-additive or additive processing? Often the fabricator doesn’t see that CFX, digital factory, as a big move for them and as something that will enhance their position in this industry.
Johnson: Fabricators are having a hard time staffing the floor for their old processes.
Carano: Workforce development is extremely difficult across the board. I’m traveling here in California and help wanted signs are out all over in manufacturing places, not just in the circuit board industry. We’re not looking necessarily for PhDs or electrical engineers with master’s degrees. We’re trying to attract those who can do the job, want to be part of the CAD/CAM or drill operator teams; someone who can handle the chemistry and run the lines.
IPC is working very hard on workforce development by reaching out to students at the college and high school levels, getting them excited about electronics and what it can do. IPC has done a great job. We need more of that. Maybe all the fabricators and assemblers in California can combine efforts to share a common message, such as, “Here’s what this industry can really do, it’s a great career for you. You can advance. It’s exciting. What we do makes things that change and improve people’s lives.”
Rebuilding Margins
Matties: We’re already on thin margins and that’s a barrier for capital investment. How do we help those margins?
Carano: As we know, there was a shift to offshore technology about 20 years ago and it hasn’t really come back. Most don’t realize that almost $20 billion of the circuit board value that gets reported, though, is in things like iPads, mobile phones, smartphones, and other things that we wouldn’t make here anyway.
We’ve never really made cellphone boards here. However, this has evolved electronics overall. There’s a melding between semiconductor and circuit boards, a convergence in the United States and Canada. There are opportunities for focusing on higher margin processes because those are protected. We wouldn’t want those over in another country; we want them here. That’s the military, aerospace, medical, automotive, and internet infrastructure that can be done here. But I’ll ask fabricators, “What’s the issue for you?” They say it’s not so much about margins, but about yields. If they had higher yields, they would make more money. The problem is, though, how do you improve yields from 90 to 95%? That could be significant.
Much of it relates to workforce development, training, certification, equipment, instrumentation, and so forth. I’ve seen several fabricators that haven’t made upgrades in their equipment, some of them for many years, and you can’t go from 3-mil lines and spaces to 1- mil lines and spaces with an entry you had 20 years ago—it’s just not going to help you. If the investment can enhance the yields, then we have the opportunity to do more. But the other thing is that with the approximately 180 fabricator buildings in the country, maybe 90 of those have fewer than 50 employees.
If a large OEM walks in and says, “I like your work and what you do here. I need 10,000 pieces a week,” how will you help them? It will take up all your capacity. Your space is limited. That’s why, in my Thought Leaders paper, I suggested that doubling capacity would include hiring more workers. That can help us bring the industry back to what we had several years ago.
Let’s face it, the technology is much further advanced today than it was 15 or 20 years ago when the market started moving to Asia. The good news is we have this opportunity to stake out our position. We don’t have to want everything, but it can be IC substrates, high-end aerospace, defense, medical, safety, and security, that’s a big deal. Cybersecurity is at the forefront, and you have all these opportunities that would be protected-type industries. If you get the automotive companies behind it, along with the various software companies for security and then of course the military aerospace, we have an opportunity to rebuild this business here in North America.
Matties: Regarding yields, though, isn’t it the management’s discipline to process control that we already have? If we already have well-managed companies, but our processes are out of control, maybe there’s a lot of improvement for management discipline.
Carano: Oh, obviously. There are investments. One of the things I’ve shown folks over the years is I can completely automate the controls of a process, several lines, for less than $50,000. That includes controllers, online controllers, online monitoring, something as simple as a conductivity probe to measure the conductivity of the water when the rinsing is poor, and we got ionic contamination. Those little probes cost about $180. You carry them in your pocket, like a pen. You just check them. I don’t see a lot of that. The focus needs to be more than just on manufacturing and getting work out the door, but also process control.
I can’t tell you how many times I went to a facility, walked over to the electroless copper line, and then looked at the electroless copper controller. “Oh, that’s a nice controller, but it’s not hooked up or not running properly and it hasn’t been calibrated lately. Why do you have it if you’re not going to use it?” That’s where variation takes place, and when there’s variation, there’s a problem.
This conversation originally appeared in the September 2022 issue of PCB007 Magazine.
Suggested Items
Atotech to Participate at KPCA Show 2024
09/03/2024 | AtotechMKS’ Atotech will participate in this year’s KPCA Show 2024 in Incheon, held at Songdo Convensia from September 4-6, 2024.
Victory Announces Breakthrough in PCB Technology with New Product Launch
08/29/2024 | openPRShenzhen Victory Electronics Technology Co., Ltd., a leader in the printed circuit board (PCB) manufacturing industry, is proud to announce the successful development of a groundbreaking new product.
Connect the Dots: Designing for Reality—Electroless Copper
08/28/2024 | Matt Stevenson -- Column: Connect the DotsRoll up your sleeves because it's time to get messy. In a recent episode of I-Connect007’s On the Line with… podcast, we discussed electroless copper deposition. This process deposits a copper layer into the through-holes and vias of what will eventually be a PCB. Electroless copper deposition feels like a black box to many people. It sort of looks like a black box, too. The boards go in one side, come out the other, and emerge differently. So, let's crack open that black box and look inside.
Maximizing ROI Through Better Wet Process Control
08/20/2024 | I-Connect007 Editorial Team“When things get out of control, the variation in your wet process begins,” says Mike Carano,. “Just because they look like good boards and may even pass electrical test, it does not necessarily mean you have good boards. Once the chemistry is headed toward the right or left side of the process control parameter cliff, the plating is compromised. If the copper is thinner than it should be, when the customer puts it into service, the board may fail after 500 cycles vs. the requisite 1,000 or 2,000 cycles. The root cause issue is that you plated 7/10ths of a mil of copper instead of one-mil of copper because you were not controlling your process. The fact that you passed your own electric test becomes inconsequential.”
The Chemical Connection: Controlling an Alkaline Etch Bath With Low Copper Loading
08/07/2024 | Don Ball -- Column: The Chemical ConnectionThis month, I wanted to continue my discussion on how much process control is actually needed for high-density circuit production. However, in the last month, I have been called on to help with a specific process control problem: how to control an alkaline etch bath when you’re not etching much copper. This problem has been cropping up more frequently as smaller shops (and a few larger ones) concentrate on low-volume, high-value plated through-hole panels such as prototypes, resistor cores, etc.