Researchers Find New Phase of Carbon, Make Diamond at Room Temperature
December 2, 2015 | North Carolina State UniversityEstimated reading time: 3 minutes
Researchers from North Carolina State University have discovered a new phase of solid carbon, called Q-carbon, which is distinct from the known phases of graphite and diamond. They have also developed a technique for using Q-carbon to make diamond-related structures at room temperature and at ambient atmospheric pressure in air.
Phases are distinct forms of the same material. Graphite is one of the solid phases of carbon; diamond is another.
“We’ve now created a third solid phase of carbon,” says Jay Narayan, the John C. Fan Distinguished Chair Professor of Materials Science and Engineering at NC State and lead author of three papers describing the work. “The only place it may be found in the natural world would be possibly in the core of some planets.”
Q-carbon has some unusual characteristics. For one thing, it is ferromagnetic – which other solid forms of carbon are not.
“We didn’t even think that was possible,” Narayan says.
In addition, Q-carbon is harder than diamond, and glows when exposed to even low levels of energy.
“Q-carbon’s strength and low work-function – its willingness to release electrons – make it very promising for developing new electronic display technologies,” Narayan says.
But Q-carbon can also be used to create a variety of single-crystal diamond objects. To understand that, you have to understand the process for creating Q-carbon.
Researchers start with a substrate, such as such as sapphire, glass or a plastic polymer. The substrate is then coated with amorphous carbon – elemental carbon that, unlike graphite or diamond, does not have a regular, well-defined crystalline structure. The carbon is then hit with a single laser pulse lasting approximately 200 nanoseconds. During this pulse, the temperature of the carbon is raised to 4,000 Kelvin (or around 3,727 degrees Celsius) and then rapidly cooled. This operation takes place at one atmosphere – the same pressure as the surrounding air.
The end result is a film of Q-carbon, and researchers can control the process to make films between 20 nanometers and 500 nanometers thick.
Page 1 of 2
Suggested Items
CTEK Shares Tips to Avoid a Dead Battery in Summer Heat
07/26/2024 | PRNewswireThe United States has seen record heat and it doesn't look like it will end anytime soon. As the heat intensifies, it's not just our bodies that need extra care and attention; CTEK says our vehicle batteries also require special consideration to ensure optimal performance and reliability.
Book Excerpt: The Printed Circuit Assembler’s Guide to... Low-Temperature Soldering, Vol. 2
06/18/2024 | I-Connect007 Editorial TeamLow-temperature solders (LTS) continue to attract serious interest from the electronics industry. These solder alloys enable the use of lower glass transition temperature (Tg) substrates and components due to the lower processing temperature, promote long-term reliability by reducing exposure to thermal excursion, and enable organizations to meet sustainability targets. In this quick-read article are sharing an excerpt from Chapter 1 of the second volume of The Printed Circuit Assembler’s Guide to... Low-Temperature Soldering.
Successful Demonstration of a Superconducting Circuit for Qubit Control within Large-scale Quantum Computer Systems
06/03/2024 | JCN NewswireIn support of the development of large-scale superconducting quantum computers, researchers with the National Institute of Advanced Industrial Science and Technology (AIST), one of the largest public research organizations in Japan, in collaboration with Yokohama National University, Tohoku University, and NEC Corporation, proposed and successfully demonstrated a superconducting circuit that can control many qubits at low temperature.
PCB Market Size to Grow by $29.06B from 2024-2028
05/17/2024 | PRNewswireThe global printed circuit board (PCB) market size is estimated to grow by USD 29.06 bn from 2024-2028, according to Technavio. The market is estimated to grow at a CAGR of over 6.6% during the forecast period.
epoxySet Launches EC-1015HP - High Temperature, Crack Resistant Epoxy Potting
05/13/2024 | epoxySetepoxySet introduces the EC-1015HP epoxy potting compound. This heat cure system is designed for temperature cycling from -55 to 180°C with significantly better crack resistance than traditional rigid epoxies. As a low viscosity encapsulant, it is used for large and small potting applications with fragile components.