Trouble in Your Tank: Understanding Interconnect Defects, Part 1
It’s Only Common Sense: Marketing Isn’t Fluff, It’s Ammunition
Driving Innovation: Mechanical and Optical Processes During Rigid-flex Production
IPC Committee Revises DSC Test Method for Tg
January 9, 2018 | IPCEstimated reading time: 1 minute
IPC’s 3-11 Laminate/Prepreg Materials Subcommittee has announced the publication of the latest revision of the test method for the determination of glass transition temperature (Tg) of copper-clad laminates (CCL). IPC-TM-650 Method 2.4.25 utilizes Differential Scanning Calorimetry (DSC) to measure the Tg of the base materials for rigid printed circuit boards. The Tg is one of the characteristics used to estimate the thermal reliability of materials used in electronics.
The key change in the document clarifies what is and what is not a phase transition as the temperature approaches the Tg for the first time. In the past, the unusual exotherms or endotherms could be interpreted as being a Tg. There are a number of reasons cited for these spurious events including stress relief, release of moisture and evaporation of residual solvent. The Pre-Scan step is needed to make the baseline more stable for the calculation of Tg1 and Tg2. The Pre-Scan takes the temperature to about 10°C above the predicted Tg1, then the sample is cooled immediately back to the starting point temperature. The determination of Tg1 is then carried out by a second scan which terminates at either 175°C or 190°C depending of the type of epoxy resin system. At the termination temperature, the specimen is held at isothermal conditions for 15 minutes before cooling again to the starting point temperature. Finally, a third scan is conducted to determine Tg2. It is Tg1 and Tg2 that are used to calculate either the cure factor or the delta Tg.
All of the IPC-TM-650 test methods can be found free of charge at the IPC website, www.IPC.org under the “Knowledge” tab.
Share on:
Testimonial
"We’re proud to call I-Connect007 a trusted partner. Their innovative approach and industry insight made our podcast collaboration a success by connecting us with the right audience and delivering real results."
Julia McCaffrey - NCAB GroupSuggested Items
Trouble in Your Tank: Understanding Interconnect Defects, Part 1
11/04/2025 | Michael Carano -- Column: Trouble in Your TankThis month, I’ll address interconnect defects (ICDs). While this defect continues to rear its ugly head, don’t despair. There are solutions, most of which center on process control and understanding the relationship of the chemistry, materials, and equipment. First, though, let’s discuss ICDs.
WestDev Announces Advanced Thermal Analysis Integration for Pulsonix PCB Design Suite
10/29/2025 | WestDev Ltd.Pulsonix, the industry-leading PCB design software from WestDev Ltd., announced a major enhancement to its design ecosystem: a direct interface between Pulsonix and ADAM Research's TRM (Thermal Risk Management) analysis software.
Designers Notebook: Power and Ground Distribution Basics
10/29/2025 | Vern Solberg -- Column: Designer's NotebookThe principal objectives to be established during the planning stage are to define the interrelationship between all component elements and confirm that there is sufficient surface area for placement, the space needed to ensure efficient circuit interconnect, and to accommodate adequate power and ground distribution.
Episode 6 of Ultra HDI Podcast Series Explores Copper-filled Microvias in Advanced PCB Design and Fabrication
10/15/2025 | I-Connect007I-Connect007 has released Episode 6 of its acclaimed On the Line with... American Standard Circuits: Ultra High Density Interconnect (UHDI) podcast series. In this episode, “Copper Filling of Vias,” host Nolan Johnson once again welcomes John Johnson, Director of Quality and Advanced Technology at American Standard Circuits, for a deep dive into the pros and cons of copper plating microvias—from both the fabricator’s and designer’s perspectives.
Nolan’s Notes: Tariffs, Technologies, and Optimization
10/01/2025 | Nolan Johnson -- Column: Nolan's NotesLast month, SMT007 Magazine spotlighted India, and boy, did we pick a good time to do so. Tariff and trade news involving India was breaking like a storm surge. The U.S. tariffs shifted India from one of the most favorable trade agreements to the least favorable. Electronics continue to be exempt for the time being, but lest you think that we’re free and clear because we manufacture electronics, steel and aluminum are specifically called out at the 50% tariff levels.