The Knowledge Base: The Era of Advanced Packaging
Standard of Excellence: Finding and Developing Future Leaders in Manufacturing
Global Sourcing Spotlight: Navigating the Variables of Holiday Schedules in Global Sourcing
STI Electronics Goes to SMTA Houston Expo
February 24, 2017 | STI Electronics, Inc.Estimated reading time: 1 minute
STI Electronics Inc. will exhibit at the SMTA Houston Expo & Tech Forum, which is scheduled to take place March 9, 2017 at the Stafford Center in Houston, Texas. Company representatives will discuss STI's Training Resources and Engineering Services divisions.
STI's Training Services division develops customized training courses to fit specific training needs. Typically, STI builds these classes around company-specific standards and specifications. STI is an IPC authorized training center for J-STD-001, IPC-A-610, IPC/WHMA-A-620, IPC-A-600 and IPC-7711/7721, and provides both Certified IPC Application Specialist (CIS) and Certified IPC Trainer (CIT) courses.
Other courses include basic soldering, wave soldering, ESD training, BGA rework and many more. It also provides operator/inspector training for through-hole and SMT soldering, conformal coating, and training to the requirements of NASA-STD-8739.1 and NASA-STD-8739.4 for Marshall Space Flight Center and its support contractors. In addition to its standardized training program support materials, STI Electronics’ Training Materials division provides unique or custom training materials including Fine Pitch Lead Free Solder Training Kits. STI is an approved distributor for IPC training materials and videos.
STI's Engineering Services division provides engineering support and specialized contract manufacturing services for the electronics manufacturing industry. From product design and manufacturability analysis to pre-production prototype and development, STI's Prototype and Development Lab is a full-service design review and preproduction facility. STI’s Microelectronics Lab was established to meet the rising need for advanced systems development and assembly.
The Microelectronics Lab specializes in state-of-the-art engineering design including current technologies such as Chip-On-Board (COB) and Multichip Module (MCM) as well as emerging technologies such as Imbedded Component/Die Technology (IC/DT).
For more information about STI Electronics, Inc., visit www.stielectronicsinc.com.
About STI Electronics, Inc.
Since 1982, STI Electronics, Inc. (STI) has been the premier full service organization for training, consulting, laboratory analysis, prototyping, and small-to-medium volume PCB assembly in the electronics industry. STI also produces a complete line of solder training kits and training support products. For more information, visit www.stielectronicsinc.com.
Share on:
Suggested Items
Book Excerpt: The Printed Circuit Assembler’s Guide to... Low-Temperature Soldering, Vol. 2, Chapter 5
12/23/2024 | I-Connect007 Editorial TeamChapter 5 introduces the advantages of using low-temperature soldering for through-hole components, including cost efficiency, reliability improvement, and reduced warpage. Also covered: the evaluation of different fluxes and the performance of HRL3 in wave soldering and selective soldering processes.
Overview of Soldering Systems With Vacuum
12/18/2024 | Dr. Paul Wild, Rehm Thermal Systems GmbHWhen soldering electronic assemblies, the focus of the vacuum application is on the removal of volatile substances from the solder joints and the associated reduction of pore formation. Particularly in the thermal management of power electronics components, pores can cause so-called hotspots with higher temperatures due to their poor heat conduction. These hotspots can lead to overheating of the components on the one hand and to thermally induced destruction of the solder structure on the other.
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
12/13/2024 | Andy Shaughnessy, I-Connect007This week, Peter Tranitz discusses the upcoming Pan-European Electronics Design Conference, set for Jan. 29-30 in Vienna, Austria. Pete Starkey brings us a review of the most recent EIPC Technical Snapshot webinar, which featured a global PCB maker update by Dr. Hayao Nakahara. Don't miss our interview with Manfred Huschka, who explains how companies can begin their own China Plus One plan. Stan Farnsworth breaks down photonic soldering and discusses its use in soldering materials that are not typically compatible. I also enjoyed Dan Beaulieu’s discussion on the value of consistency, and why just showing up for work is half the battle, especially in an inconsistent, evolving industry like ours.
Advancing Photonic Soldering
12/11/2024 | Nolan Johnson, SMT007 MagazineStan Farnsworth, director of customer satisfaction at PulseForge, discusses the advancements in photonic soldering that highlight its energy efficiency and versatility. Over the past two years, the company has refined its applications for flexible substrates and energy reduction, finding that photonic soldering allows the processing of materials that typically aren’t thermally compatible and offers significant energy savings compared to traditional methods.
Indium Introduces New ROL0 and Halogen-free Flux-cored Wire
12/11/2024 | Indium CorporationIndium Corporation announced the global availability of CW-807RS, a new high-reliability, halide- and halogen-free flux-cored wire that improves wetting speeds and cycle times for electronics assembly and robot soldering applications.