-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueSignal Integrity
If you don’t have signal integrity problems now, you will eventually. This month, our expert contributors share a variety of SI techniques that can help designers avoid ground bounce, crosstalk, parasitic issues, and much more.
Proper Floor Planning
Floor planning decisions can make or break performance, manufacturability, and timelines. This month’s contributors weigh in with their best practices for proper floor planning and specific strategies to get it right.
Showing Some Constraint
A strong design constraint strategy carefully balances a wide range of electrical and manufacturing trade-offs. This month, we explore the key requirements, common challenges, and best practices behind building an effective constraint strategy.
- Articles
- Columns
- Links
- Media kit
||| MENU - design007 Magazine
IPC High-reliability Forum and Microvia Summit Review, Part II
August 6, 2019 | Pete Starkey, I-Connect007Estimated reading time: 8 minutes

Editor’s Note: Click here to read Part I.
The Microvia Summit on May 16 was a special feature of the 2019 event, since microvia challenges and reliability issues have become of great concern to the PCB manufacturing industry. It provided updates on the work of members of the IPC V-TSL-MVIA Weak Interface Microvia Failures Technology Solutions Subcommittee and opportunities to learn about latest developments in methods to reveal and explain the presence of latent defects, identify causes and cures, and be able to consistently and confidently supply reliable products.
Dr. Michael H. Azarian of CALCE at the University of Maryland explored the effects of design and manufacturing factors on the reliability of microvia interconnects, discussing the relative strengths and weaknesses of blind, buried, isolated, staggered, and stacked microvias in HDI circuits. He stressed this point, “What looks like a relatively simple structure is actually associated with a vast number of design and process parameters that can impact reliability.”
Azarian began by considering quality issues associated with microvia filling by electrolytic copper plating. Incomplete filling or voiding could degrade reliability through localised stress concentration reducing fatigue life. He then showed several examples of corner cracks, barrel cracks, and interface separation, some attributed to inadequate process control, some to brittle fracture of the electroless copper.
Also, Azarian used finite element analysis to help determine the effects of microvia defects and process parameters on microvia lifetime, using fatigue modelling to simulate a series of solder reflow cycles followed by thermal cycling. He commented that the total strain range of the first solder reflow cycle was much larger than that of the second and third cycles due to work hardening of the copper. Fatigue life was affected by the size and shape of voids, and Azarian observed that small spherical voids actually increased the fatigue life, whereas for conical voids, the fatigue life decreased with the void size. Microvia aspect ratio also affected fatigue life when voids were present, and for a given conical void shape and volume ratio, the smaller the aspect ratio, the longer the microvia fatigue life. CALCE developed a second-order regression model to predict the cycles to failure of copper-filled stacked microvias under thermal loading and used finite element modelling for fracture analysis
Then, Azarian highlighted some of the challenges involved in microvia testing and the detection of delamination and cracking, particularly at the early stages of degradation. Advantage had been taken of the high-frequency skin effect to monitor interconnect degradation by observing changes in RF impedance. And time-domain reflectometry at high frequencies provided a further route to the early detection of interconnect failure.
Lance Auer from Conductor Analysis Technologies reported highlights from IPC committee meetings at IPC APEX EXPO 2019 and the movement towards performance-based acceptance testing for microvia reliability. He commented on the shortcomings of testing to existing IPC 6010-series specifications, which often did not identify the failures. There had been many examples of failures after passing all testing requirements, observed at in-circuit test after reflow, at environmental stress screening during box-level assembly, or in the field by the end customer. And traditional microsection techniques were not always capable of detecting many of these defects.
The IPC V-TSL-MVIA Weak Interface Microvia Failures Technology Solutions Subcommittee reported its findings during an open forum at IPC APEX EXPO 2019. In response, IPC issued a warning statement about post-fabrication microvia failures occurring during reflow but remaining undetectable at room temperature.
Several OEMs had been successfully screening lots with D-coupon testing per Method 2.6.27 Appendix A of IPC-TM-650, and IPC was moving away from traditional microsection evaluation towards performance-based acceptance testing. Reflow simulation testing for structural integrity during thermal stress was being added into the IPC-6012E qualification and performance specification for rigid printed boards.
Auer summarised the recommendations for performance-based acceptance testing agreed at the APEX 2019 committee meetings. He demonstrated the thermal profiles for reflow simulation and thermal shock testing and showed examples of change-in-resistance measurements corresponding to microvia failures. The suggested drawing notes described the design of IPC D-coupons, the number to be tested per manufacturing panel, the conditions for reflow simulation and acceptance criteria for change in resistance, the conditions for thermal shock and acceptance criteria for change in resistance, and the reporting of results.Page 1 of 2
Testimonial
"In a year when every marketing dollar mattered, I chose to keep I-Connect007 in our 2025 plan. Their commitment to high-quality, insightful content aligns with Koh Young’s values and helps readers navigate a changing industry. "
Brent Fischthal - Koh YoungSuggested Items
Indium Corporation Earns Mexico Technology Award for New Halogen-Free Flux-Cored Wire
09/18/2025 | Indium CorporationIndium Corporation recently earned a Mexico Technology Award for its new high-reliability, halide- and halogen-free flux-cored wire, CW-807RS, which improves wetting speeds and cycle times for electronics assembly and robot soldering applications.
MacDermid Alpha Showcases Advanced Interconnect Solutions at PCIM Asia 2025
09/18/2025 | MacDermid Alpha Electronics SolutionsMacDermid Alpha Electronic Solutions, a global leader in materials for power electronics and semiconductor assembly, will showcase its latest interconnect innovations in electronic interconnect materials at PCIM Asia 2025, held from September 24 to 26 at the Shanghai New International Expo Centre, Booth N5-E30
Breakthrough in Non-Contact Solder Removal Earns Kurtz Ersa 2025 Mexico Technology Award at SMTA Guadalajara
09/18/2025 | Kurtz Ersa Inc.Kurtz Ersa Inc., a leading supplier of electronics production equipment, is proud to announce that it has been awarded a 2025 Mexico Technology Award in the category of Rework & Repair for its HR 600P Automatic Rework System.
Knocking Down the Bone Pile: Best Practices for Electronic Component Salvaging
09/17/2025 | Nash Bell -- Column: Knocking Down the Bone PileElectronic component salvaging is the practice of recovering high-value devices from PCBs taken from obsolete or superseded electronic products. These components can be reused in new assemblies, reducing dependence on newly purchased parts that may be costly or subject to long lead times.
Koh Young, Fuji, and Kurtz ERSA Drive Smart Manufacturing Solutions for EV and Automotive Electronics at Kunshan, China Technical Seminar
09/11/2025 | Koh YoungKoh Young Technology, the global leader in True 3D measurement-based inspection solutions, partnered with Fuji Corporation and Kurtz ERSA to host an exclusive technical seminar for leading automotive manufacturers in East China. Held on September 4 at Fuji’s factory in Kunshan, the event gathered participants representing over 35 companies.