-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueAll About That Route
Most designers favor manual routing, but today's interactive autorouters may be changing designers' minds by allowing users more direct control. In this issue, our expert contributors discuss a variety of manual and autorouting strategies.
Creating the Ideal Data Package
Why is it so difficult to create the ideal data package? Many of these simple errors can be alleviated by paying attention to detail—and knowing what issues to look out for. So, this month, our experts weigh in on the best practices for creating the ideal design data package for your design.
Designing Through the Noise
Our experts discuss the constantly evolving world of RF design, including the many tradeoffs, material considerations, and design tips and techniques that designers and design engineers need to know to succeed in this high-frequency realm.
- Articles
- Columns
Search Console
- Links
- Media kit
||| MENU - design007 Magazine
Designing With the End in Mind—How the Meaning of DFM Will Transform in the Future
August 23, 2021 | Vince Mazur, AltiumEstimated reading time: 3 minutes

Introduction
The late American educator, author, businessman, and keynote speaker Stephen Covey coined the phrase, "Begin with the end in mind." He said, "To begin with the end in mind means to start with a clear understanding of your destination. It means to know where you’re going so that you better understand where you are now and so that the steps you take are always in the right direction.”
I recall a summer trip when a college buddy and I were on our return trek from the Havasupai campground area near the Grand Canyon. When we were almost to the top, we came across a solo hiker wearing jeans and carrying a camera, tripod, and a small bottle of water; he was about to make the eight-mile trek to Supai, Arizona. We suggested to the ill-prepared hiker to take more water, but the person chose to just continue. My friend and I looked at each other and said, “He’s not going to make it.” I am not sure how things worked out for that hiker, but I think you will agree that he was not prepared and that he certainly did not begin with the end in mind.
Designers of today’s complex printed circuit boards occasionally encounter setbacks due to their lack of early planning. Such consequences for apathy in preparation and awareness will continue to escalate along the growth curve of complexity that the industry continues to experience.
In this article, I will offer a view of how designers can be served by a design for manufacturing (DFM) mindset to help assure first-pass success. I will also provide a glimpse of the potential future of board level design along with a discussion of how the adoption of new and uncharted concepts will assist the journey of electronic product realization that lies ahead.
DFM Fluency is No Longer Optional for PCB Designers
First pass, high yield, cost optimized, and reliable PCB fabrication and assembly is the target objective for PCB designers. Fall short of this outcome, and the consequences can be quite substantial, including derailed new product introduction, sub-par profit margins, unreliable field performance, unnecessary rework, time-consuming redesign, and more. Compound this dynamic with the rapidly escalating complexity of today’s PCBs, and designers find themselves at a crossroads: Either continue the prevailing “wait and see” feedback from manufacturing after committing a project or, with little overhead, proactively and authoritatively evaluate DFM as an inherent part of the designer’s normal incremental PCB design process.
Some Design and Manufacturing Dependencies
As components are placed on a board, the design immediately inherits several design and manufacturing characteristics, such as component spacing and solderability, flying probe access, and more. All these characteristics can influence the fabrication and assembly of the PCB. In addition, the design also inherits characteristics of the parts that are largely outside of the designer’s control. Some of these characteristics include availability, cost, life cycle, performance-to-datasheet, quality, and reliability. All these represent touchpoints of risk that, left unchecked, can derail product realization.
As PCB design progresses, manufacturing characteristics can be inadvertently created, such as acid traps and edge clearances that impact bare board fabrication but may have no impact on assembly. Likewise, without manufacturer-specific DFM checks at design time, boards can be fabricated to specification, yet cannot be assembled due to limitations of the target assembler. Any of these outcomes escalates costs and delays new product introduction. Care must also be taken even when changing existing designs. If not properly revalidated, simply replacing a component can have unintended consequences, and can prevent reliable volume manufacture. This single change can impact an entire assembly run. The resultant cost and time risks can be quite high.
In addition, while not typically associated with traditional DFM, component sourcing is becoming an increasingly significant area designers must pay attention to during the entire design process. If the components cannot be reliably procured, designs cannot be manufactured.
To read this entire article, which appeared in the August 2021 issue of PCB007 Magazine, click here.