-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueSilicon to Systems: From Soup to Nuts
This month, we asked our expert contributors to weigh in on silicon to systems—what it means to PCB designers and design engineers, EDA companies, and the rest of the PCB supply chain... from soup to nuts.
Cost Drivers
In this month’s issue of Design007 Magazine, our expert contributors explain the impact of cost drivers on PCB designs and the need to consider a design budget. They discuss the myriad design cycle cost adders—hidden and not so hidden—and ways to add value.
Mechatronics
Our expert contributors discuss the advent of mechatronics in PCB design, the challenges and opportunities this creates for circuit board designers, and the benefits—to the employee and the company—of becoming a mechatronics engineer.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
EIPC Summer Conference 2022: Day 1 Review
June 28, 2022 | Pete Starkey, I-Connect007Estimated reading time: 18 minutes
EIPC board member Stig Källman, component engineer PCB at Ericsson Örebro, shared his vision and offered invaluable technical guidance and practical recommendation in his talk on setting the PCB trends and requirements for 6G PCB manufacturing.
He considers that making tomorrow’s designs with yesterday’s equipment, but capability matched, is the best way to create value and make profit. Emphasising the benefits of re-use and standardisation, his examples of standardised building blocks are Lego bricks and shipping containers. He recommends using cost-efficient layer stackups and via structures, avoiding over-design by understanding manufacturing variation, and achieving high manufacturing-panel utilisation.
He discussed PCB technology drivers: smaller lines, spaces and via sizes, high speed serial links, low-loss materials, high supply currents, optical waveguides in PCBs, and thermal management. He considered the impact of manufacturing on the environment, referencing energy efficiency, and the avoidance of hazardous substances.
Regarding laminates, he said, “Making a good soup we need the right recipes,” and regarding stackup options, he pleaded, “Don’t give us so many options! Teach us how to use the standard builds that are most produced with best tolerances to the lowest cost.” It was Ericsson´s ambition to phase out halogenated flame retardants in its products, with decisions made on a case-by-case basis, based on valid parameters, and the availability of environmentally sound alternatives.
To meet the challenges of current and future PCB technologies, Kallman’s laminate wish-list included low-Dk (less than 3) low-loss for high impedance, high-frequency RF, high-Dk (greater than 10) low-loss for low impedance, high-frequency RF, and magnetodielectric materials with a different balance between electric permittivity and magnetic permeability depending on the RF application. He sees it as important that the datasheets of halogen-free materials list their full mechanical properties, as well as data for the resin, including any fillers, covering the temperature range from -40°C to +220°C.
Discussing future material possibilities along the development path toward 6G, his view on resin development is that it should include three-way collaboration among the OEM, the material supplier, and the PCB supplier. He has a similar view on defining and measuring critical PCB design parameters that it should involve designer, manufacturer, and laminate supplier in equal proportions. And in new product introductions it is very important to ensure that the PCB shop has the opportunity to run production tests and be supported with manufacturing guidelines before any customer test boards were made.
Robrecht Belis, head of sales and PCB related business at Elsyca in Belgium, recommended a “shift-left” approach to the optimisation of bare board design, in order to identify and fix problems as early as possible in the development cycle.
As a specialist in the simulation of the PCB electroplating process, he discussed how multi-physics digital twin solutions could contribute to the optimisation of costs, product quality, time to market, and production capacity.
Quoting leading designer Rick Hartley, “Copper balancing should be done, not only at the panel level in PCB fab, but every PCB designer should be taught the many benefits of copper balancing and incorporate the concepts into their board designs.” Belis showed real examples of the significant variation in plating thickness of unbalanced designs and how thickness distribution can be optimised using proprietary software tools.
He cited testimonials confirming how the software has helped to identify critical areas at the design stage, to support engineers on the shop floor in predicting how different set-ups of designs and parameters influenced the outcome, and to accurately predict the plating parameters required to enable increased first-pass yields on new parts.
Stan Heltzel, materials engineer with the European Space Agency, described ESA’s approach to microvia reliability.
Describing PCBs as the nerves and veins of the spacecraft, he introduced the ESA web portal: European Space Components Information Exchange System, of which the PCB section (escies.org/pcb/) gives details of ESA Approved Manufacturers and Qualification Status of PCBs, ESA Qualification Status of PCB technology, ESA Approved PCB Manufacturers, ECSS standards for design of PCBs (ECSS-Q-ST-70-12C), and qualification and procurement of PCBs (ECSS-Q-ST-70-60C), as well as listing active ESA memos and checklists, historic ESA memos, and technology development and conference papers.
At the bottom of a long list of active ESA memos and checklists was ESA-TECMSP-TN-19672 Microvia Process Guidelines which gives a general process overview and specific process recommendations for laser drilling, pre-etch and cleaning, desmear, microetch, rinse, electroless copper and copper electroplating, as well as tests for qualification, lot conformance and in-process verification.
The document can also be used as a guideline for conducting a process audit. The guidelines have been drafted with support from PCB experts and experts from chemistry suppliers, and have been reviewed by the PCB manufacturers of the PCB/SMT working group.
Heltzel reviewed technology drivers: electrical performance, manufacturability, and reliability, with reliability depending on design, materials and processes, and manufacturability depending on capability and qualification. He demonstrated technology development with the example of the Apollo guidance computer of 1969 compared with a contemporary smart phone which was a million times more powerful, weighed a hundred times less and cost a thousand times less.
Introducing the HDI roadmap using a series of cross-section diagrams, he discussed the confidence interval of stress-strength analysis, failure life cycles, and microvia failure mechanisms. The approaches used by ESA to evaluate microvia designs were a review of the design with comparison to heritage and qualification, thermo-mechanical modelling, testing coupons and spare PCBs, and review of manufacturing processes. He described ESA’s procedures for Manufacturing Readiness Reviews for PCBs, which culminated in authorisation to proceed with manufacture, and discussed details of thermo-mechanical modelling, causes of strain on microvias, and microvia qualification and conformance testing.
There is work in progress using a standardised test panel in a round-robin campaign for high-reliability industry, which will provide a robust assessment of capability and reliability, secure the HDI supply chain, and validate several test methods.
It had been concluded that microvias can be used reliably, through review of design considering all critical features, and compared against a qualified envelope of technology features, with manufacturing processes optimised through mutual assessment among the supply chain. Compliance is demonstrated by test and inspection and qualification, loT conformance, in-process verification, and capability assessment.
“Stop resistance clouding your high-speed measurements,” said EIPC board member Martyn Gaudion, CEO of Polar Instruments, explaining why the distributed series resistance has to be removed from the measurement to make an accurate impedance measurement. He used 50 ohm coaxial cable to illustrate his point, different lengths of cable all having nominally the same impedance value. Impedance controlled PCB traces were, in effect, simulated coaxial cables in PCBs, so why were some PCB fabricators under the illusion that impedance changed with length? The reason was that, in fine line designs, DC resistance could cause inaccuracies in impedance measurement.
Gaudion illustrated graphically the effects of distributed series resistance and distributed shunt conductance. Distributed series resistance make the impedance appear to rise with length and it is necessary to remove its effect in order to achieve an accurate impedance measurement. Otherwise, it could be wrongly inferred that datasheet dielectric constants are incorrect.
To check whether series resistance was clouding the measurement, he suggested modelling the resistance and simulating the effect on a TDR trace by entering the trace geometry and the line length and seeing the expected result on the TDR waveform. In contrast, on broader line widths, the resistive effect could be safely ignored.
But if the DC resistance effect is ignored on fine-line traces, the TDR reading would be high compared with predictions. This could lead to concluding that the datasheet value for Er was incorrect, and might result in attempting to meet the impedance value with a revised geometry.
Polar is confident that laminate suppliers provide accurate measurements for Er and believe that de-embedding the DC resistance allows better correlation of results without artificially adjusting Er values. Page 2 of 3
Suggested Items
Atotech to Participate at KPCA Show 2024
09/03/2024 | AtotechMKS’ Atotech will participate in this year’s KPCA Show 2024 in Incheon, held at Songdo Convensia from September 4-6, 2024.
Victory Announces Breakthrough in PCB Technology with New Product Launch
08/29/2024 | openPRShenzhen Victory Electronics Technology Co., Ltd., a leader in the printed circuit board (PCB) manufacturing industry, is proud to announce the successful development of a groundbreaking new product.
Connect the Dots: Designing for Reality—Electroless Copper
08/28/2024 | Matt Stevenson -- Column: Connect the DotsRoll up your sleeves because it's time to get messy. In a recent episode of I-Connect007’s On the Line with… podcast, we discussed electroless copper deposition. This process deposits a copper layer into the through-holes and vias of what will eventually be a PCB. Electroless copper deposition feels like a black box to many people. It sort of looks like a black box, too. The boards go in one side, come out the other, and emerge differently. So, let's crack open that black box and look inside.
Maximizing ROI Through Better Wet Process Control
08/20/2024 | I-Connect007 Editorial Team“When things get out of control, the variation in your wet process begins,” says Mike Carano,. “Just because they look like good boards and may even pass electrical test, it does not necessarily mean you have good boards. Once the chemistry is headed toward the right or left side of the process control parameter cliff, the plating is compromised. If the copper is thinner than it should be, when the customer puts it into service, the board may fail after 500 cycles vs. the requisite 1,000 or 2,000 cycles. The root cause issue is that you plated 7/10ths of a mil of copper instead of one-mil of copper because you were not controlling your process. The fact that you passed your own electric test becomes inconsequential.”
The Chemical Connection: Controlling an Alkaline Etch Bath With Low Copper Loading
08/07/2024 | Don Ball -- Column: The Chemical ConnectionThis month, I wanted to continue my discussion on how much process control is actually needed for high-density circuit production. However, in the last month, I have been called on to help with a specific process control problem: how to control an alkaline etch bath when you’re not etching much copper. This problem has been cropping up more frequently as smaller shops (and a few larger ones) concentrate on low-volume, high-value plated through-hole panels such as prototypes, resistor cores, etc.