Book Excerpt: The Printed Circuit Assembler’s Guide to... Low-Temperature Soldering, Vol. 2
June 18, 2024 | I-Connect007 Editorial TeamEstimated reading time: 1 minute
The Printed Circuit Assembler’s Guide to... Low-Temperature Soldering, Vol. 2, by Morgana Ribas, et al, MacDermid Alpha Electronics Solutions
Chapter 1: Introduction to Low-temperature Soldering
Low-temperature solders (LTS) continue to attract serious interest from the electronics industry. These solder alloys enable the use of lower glass transition temperature (Tg) substrates and components due to the lower processing temperature, promote long-term reliability by reducing exposure to thermal excursion, and enable organizations to meet sustainability targets. Perhaps more significantly, low-temperature soldering is an enabling technology that mitigates warpage-induced defects of the ultra-thin, high IO chip-scale packages used in complex electronic devices. Use of higher reflow temperature Sn-Ag-Cu (SAC) solders in package-on-package (PoP) bottom and PoP memory technology can potentially result in soldering defects such as non-wet opens, solder bridging, and head-in-pillow.
The eutectic 42Sn-58Bi alloy melts at 138°C and has been considered for SMT soldering since the transition from tin-lead to lead-free solders. This alloy is quite interesting as a solder, as bismuth is one of the few elements forming a solid solution in tin. Its binary composition, lamellar microstructure, and eutectic melting point resemble that of eutectic tin-lead. However, this first-generation LTS alloy lagged behind traditional lead-free alloys in solder joint thermomechanical and drop shock reliability and limited thermal cycling performance.
The transition to lead-free solders was motivated by regulatory compliance, and SAC305 (96.5% tin, 3% silver, 0.5% copper) was chosen as the best cost-benefit alternative. As the electronics industry evolved, so did solder joint reliability requirements. Several new solders were introduced to meet specific reliability requirements.
Suggested Items
Successful Demonstration of a Superconducting Circuit for Qubit Control within Large-scale Quantum Computer Systems
06/03/2024 | JCN NewswireIn support of the development of large-scale superconducting quantum computers, researchers with the National Institute of Advanced Industrial Science and Technology (AIST), one of the largest public research organizations in Japan, in collaboration with Yokohama National University, Tohoku University, and NEC Corporation, proposed and successfully demonstrated a superconducting circuit that can control many qubits at low temperature.
PCB Market Size to Grow by $29.06B from 2024-2028
05/17/2024 | PRNewswireThe global printed circuit board (PCB) market size is estimated to grow by USD 29.06 bn from 2024-2028, according to Technavio. The market is estimated to grow at a CAGR of over 6.6% during the forecast period.
epoxySet Launches EC-1015HP - High Temperature, Crack Resistant Epoxy Potting
05/13/2024 | epoxySetepoxySet introduces the EC-1015HP epoxy potting compound. This heat cure system is designed for temperature cycling from -55 to 180°C with significantly better crack resistance than traditional rigid epoxies. As a low viscosity encapsulant, it is used for large and small potting applications with fragile components.
New Book on Low-temperature Soldering Now Available
04/17/2024 | I-Connect007I-Connect007 is pleased to announce that The Printed Circuit Assembler’s Guide to… Low-temperature Soldering, Vol. 2, by subject matter experts at MacDermid Alpha Electronics Solutions, is now available for download.
The Chemical Connection: Reducing Etch System Water Usage, Part 1
04/05/2024 | Don Ball -- Column: The Chemical ConnectionWater conservation has become an important component of the overall system design for most manufacturing operations today. Changing climate conditions and increasing populations are beginning to strain the freshwater supplies in many areas of the country. As a result, as equipment suppliers, we see an increasing number of requests for options that reduce water usage in proposed wet processing systems. Etching systems tend to use more water because of the need for close temperature control to maintain steady etch rates and the rinsing requirements for complete removal of corrosive etchants from the surface of the product before the next process step. This column contains some simple suggestions for reducing water usage in etch systems that won’t strain the budget too much.