-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueAdvancing the Advanced Materials Discussion
Moore’s Law is no more, and the advanced material solutions to grapple with this reality are surprising, stunning, and perhaps a bit daunting. Buckle up for a dive into advanced materials and a glimpse into the next chapters of electronics manufacturing.
Inventing the Future With SEL
Two years after launching its state-of-the-art PCB facility, SEL shares lessons in vision, execution, and innovation, plus insights from industry icons and technology leaders shaping the future of PCB fabrication.
Sales: From Pitch to PO
From the first cold call to finally receiving that first purchase order, the July PCB007 Magazine breaks down some critical parts of the sales stack. To up your sales game, read on!
- Articles
- Columns
- Links
- Media kit
||| MENU - pcb007 Magazine
Book Excerpt: The Printed Circuit Assembler’s Guide to... Low-Temperature Soldering, Vol. 2, Chapter 3
August 7, 2024 | I-Connect007 Editorial TeamEstimated reading time: 1 minute

Mechanical Shock and Thermomechanical Reliability of Low-temperature Solder Hybrid Joints
HRL3 uses the individual and combined effects of solid solution strengthening, precipitate and dispersion hardening, grain refinement and diffusion modifiers to balance strength, toughness, stiffness, and ductility in their respective alloy compositions. Electronic systems under normal operating conditions are exposed to a diverse range of temperatures and mechanical loads, depending on operational environment and usage. Proxy tests such as mechanical drop shock and thermal cycling are often used to predict thermal and mechanical reliability performance of solder joints in actual devices.
Solder joints are cycled between cold and hot zones during thermal cycling tests and the materials forming the solder joint—the package, the solder, the interfacial intermetallic layer, and the substrate—will expand and contract at different rates. This is generally known as coefficient of thermal expansion (CTE) mismatch, in which these variations in CTE generate shear stresses at the interfaces between these materials and potentially lead to thermomechanical fatigue. Failures through fatigue can be divided into three stages: crack initiation, crack propagation, and sudden fast failure. There are competing mechanisms promoting crack growth and closure. While stronger materials resist crack initiation better, crack propagation depends on the plastic zone ahead of the crack tip, i.e., the alloy microstructure. Thus, the need to achieve a balanced alloy composition combining strength and microstructure optimization is required for improved fatigue life and optimal performance.
A solder paste formulated with HRL3 was evaluated for drop shock and thermal cycling performance using a Cu-OSP test vehicle and SAC305 CTBGA84 packages. Therefore, upon using the low-temperature solder paste to attach these packages to a PCB, a hybrid (or heterogeneous) LTS/SAC305 solder joint is formed. The solder paste was screen printed on a PCB by using two stencil apertures, 11 and 14 mil. Table 3.1 shows the corresponding paste volume to ball volume ratios (0.6 and 0.8) that enabled investigating the effect of paste volume on the mechanical and thermal reliability of their solder joints.
These PCBs were reflowed using the profiles shown in Figure 3.1. The HRL3 alloy was evaluated using two peak temperatures, 165°C and 175°C, while SAC305 was reflowed using its typical 245°C (all within +/-5°C) peak profile.
Testimonial
"We’re proud to call I-Connect007 a trusted partner. Their innovative approach and industry insight made our podcast collaboration a success by connecting us with the right audience and delivering real results."
Julia McCaffrey - NCAB GroupSuggested Items
Koh Young, Fuji, and Kurtz ERSA Drive Smart Manufacturing Solutions for EV and Automotive Electronics at Kunshan, China Technical Seminar
09/11/2025 | Koh YoungKoh Young Technology, the global leader in True 3D measurement-based inspection solutions, partnered with Fuji Corporation and Kurtz ERSA to host an exclusive technical seminar for leading automotive manufacturers in East China. Held on September 4 at Fuji’s factory in Kunshan, the event gathered participants representing over 35 companies.
MacDermid Alpha Presents at SMTA New Delhi, Bangalore Chapter, on Flux–OSP Interaction
09/09/2025 | MacDermid Alpha Electronics SolutionsMacDermid Alpha contributes technical insights on OSP solderability at the Bangalore Chapter, SMTA reinforcing commitment to knowledge-sharing and industry collaboration.
Electra’s ElectraJet EMJ110 Inkjet Soldermask Now in Black & Blue at Sunrise Electronics
09/08/2025 | Electra Polymers LtdFollowing the successful deployment of Electra’s Green EMJ110 Inkjet Soldermask on KLA’s Orbotech Neos™ platform at Sunrise Electronics in Elk Grove Village, Illinois, production has now moved beyond green.
Absolute EMS: The Science of the Perfect Solder Joint
09/05/2025 | Absolute EMS, Inc.Absolute EMS, Inc., a six-time award-winning provider of fast turnaround, turnkey contract electronic manufacturing services (EMS), is drawing attention to the critical role of 3D Solder Paste Inspection (SPI) in ensuring the reliability of both FLEX and rigid printed circuit board assemblies (PCBAs).
Indium Corporation to Highlight High-Reliability Solder Solutions at SMTA Guadalajara Expo
09/04/2025 | Indium CorporationIndium Corporation, a leading materials refiner, smelter, manufacturer, and supplier to the global electronics, semiconductor, thin-film, and thermal management markets, will feature a range of innovative, high-reliability solder products for printed circuit board assembly (PCBA) at the SMTA Guadalajara Expo and Tech Forum, to be held September 17-18 in Guadalajara, Mexico.