-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLearning to Speak ‘Fab’
Our expert contributors clear up many of the miscommunication problems between PCB designers and their fab and assembly stakeholders. As you will see, a little extra planning early in the design cycle can go a long way toward maintaining open lines of communication with the fab and assembly folks.
Training New Designers
Where will we find the next generation of PCB designers and design engineers? Once we locate them, how will we train and educate them? What will PCB designers of the future need to master to deal with tomorrow’s technology?
The Designer of the Future
Our expert contributors peer into their crystal balls and offer their thoughts on the designers and design engineers of tomorrow, and what their jobs will look like.
- Articles
- Columns
Search Console
- Links
- Media kit
||| MENU - design007 Magazine
PCB Carolina’s Formula: Industry Experts and Catered Food
November 18, 2024 | Andy Shaughnessy, Design007 MagazineEstimated reading time: 1 minute
PCB Carolina organizers at the Better Boards design bureau seem to have found the perfect formula: Industry experts plus catered food equals a constantly expanding show. This one-day tabletop show has been growing for two decades, and that trendline continued with this year’s event on November 13.
Located in NC State’s McKimmon Conference and Training Center in Raleigh, North Carolina, PCB Carolina has gone from a small local show to a regional event that draws exhibitors and attendees from around the U.S.
The day started with breakfast and a keynote speech by Saugat Sen of Cadence Design Systems. The 16 technical sessions covered everything from PCB design and DFM techniques to assembly and product safety. The show squeezed quite a bit into a one-day event.
Once again, the show floor was sold out, with exhibitors setting up booths in the lobby and in several classrooms. Exhibitors represented the entire PCB supply chain, including EDA companies, fabricators, CEMs, component and laminate suppliers, distributors, and service providers.
Show manager Randy Faucette said the number of attendees was up 8% over last year. In addition to PCB designers and electrical engineers, I spoke with attendees from the semiconductor, packaging, fab, and assembly segments. Most attendees were from the RTP areas, but some drove five hours or more to the show.
Some repeat attendees joked that the catered food was enough to draw PCB technologists back year after year. After enjoying a lunch of barbecued brisket and a Mexican dinner with local craft beers, it’s hard to disagree. No one likes boxed lunches.
Over the years, I’ve met technologists who only attend PCB Carolina, because their companies don’t have the budget to send them to the bigger shows in our industry. Regional shows provide a real service, and PCB Carolina’s managers make sure that you won’t have to eat “conference chicken” while staying up to date with changes in technology.
Suggested Items
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
03/28/2025 | Andy Shaughnessy, I-Connect007I’ve spent my week recovering from a busy and interesting week in Anaheim for the 25th IPC APEX EXPO. I think back to my first APEX EXPO, and the changes since then are too numerous to count. I first attended in 2004, also in Anaheim, back when there was almost no design content in the conference or expo portions of the show. It was just a few years after the downturn, and attendees and exhibitors alike were skittish, almost afraid to show confidence in our industry. A few unemployed design friends handed out copies of their resumes. Travel budgets were still down, and the aisles weren’t exactly packed with traffic.
Real Time with... IPC APEX EXPO 2025: MKS' Atotech—Leading Innovations in Semiconductor Solutions
03/28/2025 | Real Time with...IPC APEX EXPOIn this interview, Marcy LaRont speaks with Kuldip Johal, CTO, MKS’ Atotech. Based in Boston, MKS operates in vacuum solutions, photonics, and specifically for the Atotech division, material solutions. MKS significantly impacts the semiconductor industry, supplying components for up to 85% of global semiconductor tools and covers processes and materials for 70% of PCB manufacturing steps.
TTCI and TTC-LLC to Exhibit and Sponsor at SMTA Tech & Expo Forums in Dallas and Houston
03/27/2025 | The Test Connection Inc.The Test Connection Inc. (TTCI), a leading provider of electronic test and manufacturing solutions, and The Training Connection LLC (TTC-LLC) are proud to announce their participation as exhibitors and sponsors at the upcoming Dallas SMTA Tech & Expo Forum on April 1, 2025.
Electronics Industry Leaders Available to Comment on Two-Year Anniversary of Defense Production Act
03/27/2025 | IPCToday marks two years since President Biden issued Presidential Determination 2023-06, which invoked the Defense Production Act (DPA) to stimulate U.S. investment in the manufacturing of printed circuit boards (PCBs) and related technologies.
Real Time with... IPC APEX EXPO 2025: Emphasizing Sustainability in PCB Design with Summit Interconnect
03/27/2025 | Real Time with...IPC APEX EXPOAndy Shaughnessy and Gerry Partida of Summit Interconnect discuss the rising customer interest in sustainability within PCB design. Gerry points out that many designs neglect sustainability, resulting in low yields and higher costs. The conversation stresses the importance of adhering to PCB standards and collaborating with fabricators to tackle design challenges and enhance sustainability.