-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueProper Floor Planning
Floor planning decisions can make or break performance, manufacturability, and timelines. This month’s contributors weigh in with their best practices for proper floor planning and specific strategies to get it right.
Showing Some Constraint
A strong design constraint strategy carefully balances a wide range of electrical and manufacturing trade-offs. This month, we explore the key requirements, common challenges, and best practices behind building an effective constraint strategy.
All About That Route
Most designers favor manual routing, but today's interactive autorouters may be changing designers' minds by allowing users more direct control. In this issue, our expert contributors discuss a variety of manual and autorouting strategies.
- Articles
- Columns
- Links
- Media kit
||| MENU - design007 Magazine
Kris Moyer Discusses His Emerging Design Technologies Class
September 4, 2025 | Marcy LaRont, I-Connect007Estimated reading time: 4 minutes

Kris Moyer, a design instructor for the Global Electronics Association, will be teaching his advanced PCB design class this fall. If you’re ready to level up your design education, you won’t want to miss this interview.
The PCB Design for Emerging Design Technologies course is designed to provide the skills necessary to create PCB/PBA designs that require cutting-edge emerging design technologies and comply with all necessary IPC standards, including new standards being developed in this area.
Kris lives in his RV, usually on his property near Sacramento, but he’s been known to travel thousands of miles for a great camping spot. I asked Kris to give us an update on his summer activities and a preview of what attendees can expect to get out of this six-week class.
Marcy LaRont: Kris, it’s always good to catch up with you. Where are you right now, and have you been hiking a lot this summer?
Kris Moyer: I was just in Grover Hot Springs near Markleeville, California. I spent one weekend there, and now I am back in Sacramento. In mid-August, I was at William Kent Campground near Lake Tahoe, California. I’ve been doing lots of hiking this summer. With my mom's passing in May, and following her last wishes, she was cremated, and she wanted her ashes spread in all the places she enjoyed. So, each camping weekend, I go on a hike with my friends and spread a bit of Mom at each location I visit.
LaRont: That’s great. Now, your online advanced design course, PCB Design for Emerging Design Technologies, is coming up in early October. Please explain what you mean by “emerging design technologies.”
Moyer: This course is intended to discuss the newest technologies used in the electronics industry, including technologies for which no standards have been defined yet.
LaRont: Through your work as an instructor, you see designers of different levels and the challenges they struggle with. What specific things do you think attendees will find most valuable in this course? Are any particular technologies getting a lot of traction right now?
Moyer: Yes, this course will cover two primary technologies. The first is ultra HDI. We have discussed UHDI in several Design007 Magazine articles and interviews, and I am putting together concepts for designing PCBs using its features. UHDI is necessary for designs that incorporate the newest micro-miniature package options.
The second is 3D printed electronics. While I do cover printed electronics in the current Advanced Design Concepts course, those are more in line with traditional 2D printed materials, similar to inkjet printers or other printed media. In the new course, we will be looking at 3D printing the structures in the electronic systems.
The 3D printed electronics are becoming more prevalent as silicon-to-systems design is taking a more central role in design. This is the logical extension of rigid-flex PCB design. Rather than producing a series of flat PCBs connected with flex circuits that are folded into the shape necessary for the product, with 3D printing, the solid structure is created in the final shape configuration with parts mounted on all the different surfaces, rather than just the top and bottom surfaces like traditional boards
LaRont: This course is broken up into 12 sessions. What details can you provide?
Moyer: The course is six weeks long, with two weekly sessions on Tuesdays and Thursdays. Each session is two hours long. The first session of each week is new theory content. The second session is a hands-on practice of that theory using a leading ECAD design tool. The courses are designed to be similar to live college classes in that they are interactive and students are encouraged to ask questions during class rather than waiting until the end for a Q&A session.
LaRont: Will the recording be available to registrants after the live virtual sessions?
Moyer: This class is designed to be a live, online instructor-led class. It will be recorded while being presented and typically posted to the course page by the next business day. Registered students will have access to the course content, including the videos, for one year after completion of the course.
LaRont: Kris, what makes these types of educational opportunities so valuable for attendees?
Moyer: These live, instructor-led courses allow students to gain interactive access to the instructor's knowledge and experience. Students can ask questions and gain additional clarification and insight on any design topic that may be important to them.
LaRont: Is there anything else you would like potential registrants to know about this course?
Moyer: These IPC courses have proven to be an excellent source of knowledge, allowing our students to develop successful, high-quality, high-first-pass yield, and high-reliability designs for their applications.
For more information or to register for this class, click here.
PCB Design for Emerging Design Technologies
Six-week course runs from October 7 – November 13
Two-hour classes, Tuesdays and Thursdays
10 a.m. Pacific/1 p.m. Eastern
Testimonial
"We’re proud to call I-Connect007 a trusted partner. Their innovative approach and industry insight made our podcast collaboration a success by connecting us with the right audience and delivering real results."
Julia McCaffrey - NCAB GroupSuggested Items
Synopsys Announces Expanding AI Capabilities for its Leading EDA Solutions
09/04/2025 | SynopsysSynopsys announced expanding Synopsys.ai™ Copilot generative AI (GenAI) capabilities for its industry-leading semiconductor design solutions, enabling semiconductor engineering teams to accelerate development timelines, support significantly more complex designs, and increase engineering velocity amidst a workforce shortage.
UHDI Fundamentals: UHDI Technology and Industry 4.0
09/03/2025 | Anaya Vardya, American Standard CircuitsUltra high density interconnect (UHDI) technology is rapidly transforming how smart systems are designed and deployed in the context of Industry 4.0. With its capacity to support highly miniaturized, high-performance, and densely packed electronics, UHDI is a critical enabler of the smart, connected, and automated industrial future. Here, I’ll explore the synergy between UHDI and Industry 4.0 technologies, highlighting applications, benefits, and future directions.
Talking with Tamara: Floor Planning Policies
09/04/2025 | Andy Shaughnessy, Design007 MagazineTamara Jovanovic is an electrical engineer with Masimo, a medical equipment manufacturer. She’s been designing PCBs for seven years and earned a master’s degree in electrical engineering in 2022. I asked Tamara to share her thoughts on floor planning—the challenges, techniques, and advice for designers setting up floor planning strategies.
Pentalogix Launches ViewMate Essentials to Ensure PCB Designs are Manufacturing-Ready
09/03/2025 | PentaLogixPentalogix, Inc., a leader in PCB design solutions, announced the launch of ViewMate Essentials, an advanced CAM package designed to enhance the workflow of PCB designers. Available starting September 2nd, 2025, ViewMate Essentials enables designers to view, edit, and manage PCB manufacturing files with exceptional precision, facilitating seamless collaboration with PCB fabricators and assemblers.
The Global Electronics Association Launches Design Village at APEX EXPO 2026
09/02/2025 | Global Electronics AssociationAPEX EXPO, the hallmark electronics tradeshow hosted by the Global Electronics Association, announced the launch of the Design Village, a new feature in the exhibit hall that will unite the world’s leading innovators and showcase next-generation solutions for the electronics industry.