The Government Circuit: Three Inescapable Conclusions About Global Trade Policies
Global Citizenship: The Global Push for Digital Inclusion
Knocking Down the Bone Pile: Addressing End-of-life Component Solderability Issues, Part 4
Sierra Circuits Inc. Chooses atg A9L Flying Probe Technology for High-speed Electrical Test
April 1, 2025 | atg Luther & Maelzer GmbHEstimated reading time: Less than a minute
atg Luther & Maelzer GmbH confirms delivery of high-speed bare board testing technology to PCB fabricator Sierra Circuits Inc. in Sunnyvale, CA.
Consistent with the on-going investment in leading edge technologies at Sierra Circuits Inc., the A9L, 8 head, double-sided large format, high speed, high accuracy flying probe test system represents the latest addition to their test department. The new atg technology enables Sierra Circuits Inc. to test the latest ultra-fine designs while helping to reach industry leading throughput goals.
atg’s A9L can test pad sizes down to 35 micron and is capable of testing products up to a size of 36” x 26”. The A9L eliminates limitations due to test point density or fine-pitch contacts and features embedded component test, 4-wire Kelvin measurement capability with an accuracy of +/- 0,025 mΩ, HPOT and latent testing, in combination with a test speed of up to 230 measurements/second.
From their state-of-the-art PCB manufacturing facility in the heart of Silicon Valley, Sierra Circuits Inc. offers a complete line of PCB layout, fabrication, and assembly services. With almost 40 years of experience manufacturing highly complex PCB products, Sierra Circuits Inc. is one of the leading PCB manufacturers in North America.
Share on:
Suggested Items
TRI to Exhibit at SMTA Queretaro Expo 2025
07/16/2025 | TRITest Research, Inc. (TRI), the leading provider of test and inspection systems for the electronics manufacturing industry, is pleased to announce plans to exhibit at the SMTA Querétaro Expo 2025, scheduled to take place on July 24, 2025, at the Querétaro Centro de Congresos y Teatro Metropolitano.
Knocking Down the Bone Pile: Addressing End-of-life Component Solderability Issues, Part 4
07/16/2025 | Nash Bell -- Column: Knocking Down the Bone PileIn 1983, the Department of Defense identified that over 40% of military electronic system failures in the field were electrical, with approximately 50% attributed to poor solder connections. Investigations revealed that plated finishes, typically nickel or tin, were porous and non-intermetallic.
Meet the Author Podcast: Martyn Gaudion Unpacks the Secrets of High-Speed PCB Design
07/16/2025 | I-Connect007In this special Meet the Author episode of the On the Line with… podcast, Nolan Johnson sits down with Martyn Gaudion, signal integrity expert, managing director of Polar Instruments, and three-time author in I-Connect007’s popular The Printed Circuit Designer’s Guide to... series.
TTCI Joins Printed Circuit Engineering Association to Strengthen Design-to-Test Collaboration and Workforce Development
07/09/2025 | The Test Connection Inc.The Test Connection Inc. (TTCI), a leading provider of electronic test and manufacturing solutions, is proud to announce its membership in the Printed Circuit Engineering Association (PCEA), further expanding the company’s efforts to support cross-functional collaboration, industry standards, and technical education in the printed circuit design and manufacturing community.
Study on Resonance Mitigation in Metallic Shielding for Integrated Circuits
07/08/2025 | Maria Cuesta-Martin, Victor Martinez, Vidal Gonzalez Aguado, Würth ElektronikInherent cavity resonant modes often lead to significant degradation of shielding effectiveness, responsible for unwanted electromagnetic coupling. Cavity resonant modes of the metal shielding enclosure can produce two adverse problems: the mutual coupling among different RF modules and shielding effectiveness reduction of the metal enclosure. The cabinets serve to shield certain components from electromagnetic interference (EMI). However, these cavities present some resonance peaks at 5 GHz, making it impossible to use them at higher frequencies.