Marcy’s Musings: From Pitch to PO—The Sales Stack
It’s Only Common Sense: Knowing When to Walk Away
Dan’s Biz Bookshelf: ‘Elevate: Push Beyond Your Limits'
Brooks' Bits: Your Traces Have Hot Spots!
August 24, 2016 | Douglas G. Brooks, PhDEstimated reading time: 1 minute
Your traces have hot spots. At least, those that carry a moderate current do. Surprised? Well, I was a little surprised, too, when I looked at this a little more closely.
One chapter in my recent book focuses on fusing current. It contains the image (Figure 1), captured on video, which shows a 20 mil wide trace that had been heated for about 15 minutes, just at the moment of fusing. There are several interesting things in this image, especially how the smoke is blown out from under the trace at certain points with considerable pressure. But note that the trace fuses at a point, not everywhere along the trace. It is clear from observation that the trace is much hotter at some points than at others.
Figure 2 appeared in a separate article published in 2010. (It has been enhanced after some collaboration with the author of that article.) The image shows a trace being heated to the melting point. At this stage, the hottest portions of the trace are over 600°C, but other areas remain in the 200°C temperature range.
The reasons for the temperature variation at high temperatures are not too hard to understand. There may be minor contamination under the trace or in the copper that accounts for it. Certainly, at higher temperatures (say above about 300°C) the board may begin to delaminate, severely disrupting its cooling characteristics. There may be small variations in trace width or thickness that help account for the delam, and these effects would be randomly distributed along the length of the trace.
But in a variety of lower-temperature studies, I personally took trace temperature measurements using a small thermocouple. I noticed that if I moved the thermocouple slightly, I would get a different temperature reading. Not by much, maybe 1.0° or 1.5°C. This is more than the resolution of the thermocouple, but not enough for me to be satisfied that the differences were real. So I began to wonder if these variations in temperature appeared at lower trace temperatures, say in the 40°C. range.
To read this entire article, which appeared in the August 2016 issue of The PCB Design Magazine, click here.
Share on:
Suggested Items
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
07/18/2025 | Nolan Johnson, I-Connect007It may be the middle of the summer, but the news doesn’t quit, and there’s plenty to talk about this week, whether you’re talking technical or on a global scale. When I have to choose six items instead of my regular five, you know it’s good. I start by highlighting my interview with Martyn Gaudion on his latest book, share some concerning tariff news, follow that up with some promising (and not-so-promising) investments, and feature a paper from last January’s inaugural Pan-European Design Conference.
Elephantech Launches World’s Smallest-Class Copper Nanofiller
07/17/2025 | ElephantechJapanese deep-tech startup Elephantech has launched its cutting-edge 15 nm class copper nanofiller – the smallest class available globally. This breakthrough makes Elephantech one of the first companies in the world to provide such advanced material for commercial use.
Copper Price Surge Raises Alarms for Electronics
07/15/2025 | Global Electronics Association Advocacy and Government Relations TeamThe copper market is experiencing major turbulence in the wake of U.S. President Donald Trump’s announcement of a 50% tariff on imported copper effective Aug. 1. Recent news reports, including from the New York Times, sent U.S. copper futures soaring to record highs, climbing nearly 13% in a single day as manufacturers braced for supply shocks and surging costs.
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
07/11/2025 | Andy Shaughnessy, Design007 MagazineThis week, we have quite a variety of news items and articles for you. News continues to stream out of Washington, D.C., with tariffs rearing their controversial head again. Because these tariffs are targeted at overseas copper manufacturers, this news has a direct effect on our industry.I-Connect007 Editor’s Choice: Five Must-Reads for the Week
Digital Twin Concept in Copper Electroplating Process Performance
07/11/2025 | Aga Franczak, Robrecht Belis, Elsyca N.V.PCB manufacturing involves transforming a design into a physical board while meeting specific requirements. Understanding these design specifications is crucial, as they directly impact the PCB's fabrication process, performance, and yield rate. One key design specification is copper thieving—the addition of “dummy” pads across the surface that are plated along with the features designed on the outer layers. The purpose of the process is to provide a uniform distribution of copper across the outer layers to make the plating current density and plating in the holes more uniform.