Fresh PCB Concepts: Assembly Challenges with Micro Components and Standard Solder Mask Practices
Elementary Mr. Watson: Retro Routers vs. Modern Boards—The Silent Struggle on Your Screen
Beyond Design: The Metamorphosis of the PCB Router
Fault-Finding: It’s All About Prevention, not Blame
September 18, 2017 | Kelly Dack, CID+, EPTACEstimated reading time: 1 minute
There are thousands of things that can go wrong during the design and manufacture of a PCB assembly. One might say that it is an absolute miracle when a PCB goes through all of its phases—design, fabrication and assembly—and operates successfully!
But what happens when something goes wrong? The flow of an entire project can be disrupted when a problem is discovered on the PCB. What happens when a short or an open circuit is discovered; a part lead won’t fit into a hole or an entire connector pattern is designed backward? Murphy’s Law ensures us that PCB issues are discovered at the most critical periods of a PCB’s design and manufacturing cycles.
So, it is not a question of if a problem might be found, but when. A designer must be aware that their management and their customers may be less in tune with the technical aspects of the why their design is running late or doesn’t work. But like the Queen of Hearts in “Alice in Wonderland,” there are some management and customer cultures out there who naively attempt to resolve problems by seeking out the culprits and shouting “Off with their heads!”
Seasoned PCB designers have learned that jumping to a conclusion without carefully examining all of the possibilities is not only a waste of time, but can be devastating to the carefully cultivated relationships. A quick read of almost any psychology article on “fault” or “blame” will coax the reader away from adding to a problem by placing fault or blame on others. It is far more productive to examine yourself first before shining forth as part of a solution. Focus on process rather than personalities.
Companies in the PCB industry have adapted a widely accepted methodology for sleuthing out the source of problems which might occur during a product development cycle: root cause analysis. Root cause analysis (RCA) began in the 1950s as a study by NASA and had its origins in rocket design. RCA methods are used to methodically identify root causes of events, rather than to simply address the symptomatic result.
To read this entire article, which appeared in the August 2017 issue of The PCB Design Magazine, click here.
Share on:
Suggested Items
DownStream Acquisition Fits Siemens’ ‘Left-Shift’ Model
06/26/2025 | Andy Shaughnessy, I-Connect007I recently spoke to DownStream Technologies founder Joe Clark about the company’s acquisition by Siemens. We were later joined by A.J. Incorvaia, Siemens’ senior VP of electronic board systems. Joe discussed how he, Rick Almeida, and Ken Tepper launched the company in the months after 9/11 and how the acquisition came about. A.J. provides some background on the acquisition and explains why the companies’ tools are complementary.
Elementary Mr. Watson: Retro Routers vs. Modern Boards—The Silent Struggle on Your Screen
06/26/2025 | John Watson -- Column: Elementary, Mr. WatsonThere's a story about a young woman preparing a holiday ham. Before putting it in the pan, she cuts off the ends. When asked why, she shrugs and says, "That's how my mom always did it." She asks her mother, who gives the same answer. Eventually, the question reaches Grandma, who laughs and says, "Oh, I only cut the ends off because my pan was too small." This story is a powerful analogy for how many PCB designers approach routing today.
Siemens Turbocharges Semiconductor and PCB Design Portfolio with Generative and Agentic AI
06/24/2025 | SiemensAt the 2025 Design Automation Conference, Siemens Digital Industries Software today unveiled its AI-enhanced toolset for the EDA design flow.
Cadence AI Autorouter May Transform the Landscape
06/19/2025 | Andy Shaughnessy, Design007 MagazinePatrick Davis, product management director with Cadence Design Systems, discusses advancements in autorouting technology, including AI. He emphasizes a holistic approach that enhances placement and power distribution before routing. He points out that younger engineers seem more likely to embrace autorouting, while the veteran designers are still wary of giving up too much control. Will AI help autorouters finally gain industry-wide acceptance?
Beyond Design: The Metamorphosis of the PCB Router
06/18/2025 | Barry Olney -- Column: Beyond DesignThe traditional PCB design process is often time-consuming and labor-intensive. Routing a complex PCB layout can consume up to 30% of a designer’s time, and addressing this issue is not straightforward. We have all encountered this scenario: You spend hours setting the constraints and finally hit the Go button, only to be surprised by the lack of visual appeal and the obvious flaws in the result.