The Marketing Minute: A Brand Visibility Playbook—Get Seen, Heard, and Remembered
American Made Advocacy: Supporting the Entire PCB Ecosystem—Materials to OEMs
Marcy's Musings: The Hole Truth—Via Integrity in an HDI World
TUC Announces Plant Expansion and Financial Report
December 26, 2017 | TUCEstimated reading time: 1 minute
Taiwan Union Technology Corporation (TUC), manufacturer of copper-clad laminates (CCL) and prepregs for electronic interconnects, reported first half earnings per share of NT2.36. TUC continues to expand capacity for high-speed substrates, spending NT140 million to buy an adjacent property. TUC is expected to invest NT1.46 billion to build and equip the state of the art plant. The new plant is expected to begin operations in 2019.
TUC production includes CCL, prepregs and high-speed substrates. CCL and prepregs counted for about 80% of the shipments and high-speed substrates for about 20%. The main production base includes one plant and company headquarters in Taiwan and two plants in mainland China located in Changshu and Zhongshan. TUC’s focus has been on high Tg base materials as well as high-speed, low loss products. For IC carrier material, the dielectric constant (Dk) will affect the signal transmission speed, and the dissipation factor (Df) will affect the quality of the signal transmission. When these two factors are optimized in the base material, lower signal delay (Signal Propagation Delay Time) and reduced signal transmission loss (Signal Transmission Loss) can be achieved. With these factors in mind, TUC developed base materials with fast transmission speed and improved signal integrity with its Thunderclad line of products. The market demand for these products has been mainly in servers, base control panels and storage devices. TUC enjoys a leading technological position in the high Tg and low Dk products for the domestic industry. TUC is the first to mass produce for the 100G switch substrates.
Benefiting from the high growth of high-speed transmission products, TUC performed well in the past two years. In the first half of 2017, consolidated revenue was NT7.81 billion, the operating gross profit was NT1.67 billion, and the consolidated gross profit margin was 21.4%. Finally, the pre-tax profit of NT760 million was realized with an after-tax profit of NT570 million, generating earnings per share of NT2.36.
Share on:
Suggested Items
The Evolution of Picosecond Laser Drilling
06/19/2025 | Marcy LaRont, PCB007 MagazineIs it hard to imagine a single laser pulse reduced not only from nanoseconds to picoseconds in its pulse duration, but even to femtoseconds? Well, buckle up because it seems we are there. In this interview, Dr. Stefan Rung, technical director of laser machines at Schmoll Maschinen GmbH, traces the technology trajectory of the laser drill from the CO2 laser to cutting-edge picosecond and hybrid laser drilling systems, highlighting the benefits and limitations of each method, and demonstrating how laser innovations are shaping the future of PCB fabrication.
Day 2: More Cutting-edge Insights at the EIPC Summer Conference
06/18/2025 | Pete Starkey, I-Connect007The European Institute for the PCB Community (EIPC) summer conference took place this year in Edinburgh, Scotland, June 3-4. This is the third of three articles on the conference. The other two cover Day 1’s sessions and the opening keynote speech. Below is a recap of the second day’s sessions.
Day 1: Cutting Edge Insights at the EIPC Summer Conference
06/17/2025 | Pete Starkey, I-Connect007The European Institute for the PCB Community (EIPC) Summer Conference took place this year in Edinburgh, Scotland, June 3-4. This is the second of three articles on the conference. The other two cover the keynote speeches and Day 2 of the technical conference. Below is a recap of the first day’s sessions.
Preventing Surface Prep Defects and Ensuring Reliability
06/10/2025 | Marcy LaRont, PCB007 MagazineIn printed circuit board (PCB) fabrication, surface preparation is a critical process that ensures strong adhesion, reliable plating, and long-term product performance. Without proper surface treatment, manufacturers may encounter defects such as delamination, poor solder mask adhesion, and plating failures. This article examines key surface preparation techniques, common defects resulting from improper processes, and real-world case studies that illustrate best practices.
RF PCB Design Tips and Tricks
05/08/2025 | Cherie Litson, EPTAC MIT CID/CID+There are many great books, videos, and information online about designing PCBs for RF circuits. A few of my favorite RF sources are Hans Rosenberg, Stephen Chavez, and Rick Hartley, but there are many more. These PCB design engineers have a very good perspective on what it takes to take an RF design from schematic concept to PCB layout.