Solder Printing: A 1:1 Ratio of Technical and Creative
Global Sourcing Spotlight: A World Full of Product Expertise
The Knowledge Base: Enhancing Customer Loyalty and Product QualityHenkel Tackles Challenging 5G, Power, Automotive and Aerospace Applications at IPC APEX
January 17, 2020 | HenkelEstimated reading time: 2 minutes
At next month’s IPC APEX EXPO electronics event in San Diego, CA, Henkel’s exhibit and conference participation will highlight the materials leader’s latest innovations and the scope of its portfolio, which offers ‘solutions across the board’ for multiple applications. Henkel’s aggressive product development initiatives have resulted in advanced thermal management materials for next-generation 5G infrastructure systems, semi-sintering materials that address demanding aerospace reliability requirements, and low voiding solder pastes that help ensure electrical and mechanical reliability for power electronics.
Visitors to IPC APEX EXPO are invited to meet with Henkel technologists in booth # 3603 to learn more about:
High Performance Materials for Tough Operational Environments
- High Thermal Conductivity, Ultra-Low Modulus TIM -- Controlling the heat generated by 5G telecom infrastructure and consumer mobility devices while minimizing assembly stress is becoming more difficult as power densities rise within increasingly smaller footprints. Soft, compliant, ultra-low modulus BERGQUIST® GAP PAD® TGP 10000ULM thermal interface material (TIM) strikes this balance, with a thermal conductivity of 10.0 W/m-K, which is among the highest lambda values available on the market today for low modulus TIM pads.
- Low Voiding Solder Paste – The need to minimize internal temperature in order to extend component lifetime is driving the requirement for low voiding solder materials. Eliminating hot spot formation presumed to be caused by voids in the interconnect material helps improve electrical and mechanical reliability, which is critically important for power and industrial automation applications which are often operational 24/7. LOCTITE GC 18 is the latest addition to the award-winning LOCTITE GC materials portfolio with market-leading performance of less than 25% voiding on large QFNs (>8.0 mm x 8.0 mm) and <10% on small QFNs (< 8.0 mm x 8.0 mm).
- Semi-sintering Materials -- Aerospace applications, most notably radar systems, require board-level assemblies and power semiconductors to cope with high current densities and effective heat dissipation. Simultaneously, performance chips that integrate Gallium Nitride (GaN), Gallium Arsenide (GaAs) and Silicon Carbide (SiC) have higher operating temperatures (>200°C) which soft solder and silver-based adhesives cannot survive. LOCTITE® ABLESTIK® ICP 9000 series semi-sintering interconnect materials offer exceptional thermal performance to cope with the demands of high-power density aerospace applications.
Technology Expertise
For conference attendees that want to dive deeper into materials capabilities and practical application, presentations from several Henkel technologists offer additional educational opportunities. The following paper and poster presentations will be delivered throughout the three-day event:
- Course: Thermal Management Using Thermal Interface Materials, Dr. Rita Mohanty, Henkel Director of Application Engineering and Technical Customer Service, Feb. 3, 9:00 am – 12:00 pm.
- Paper Presentation: A Hybrid Sintering Technology for High-power Density Devices Used in Aerospace Applications, Yuan (David) Zhao, Henkel Principal Engineer, Technical Customer Service, Feb. 5, 1:30 pm – 3:00 pm.
- Paper Presentation: Liquid Dispensed Thermal Materials for High-Volume Manufacturing, Sanjay Mirsa, Henkel Senior Scientific Principal, Feb. 6, 9:00 am – 10:00 am.
- Poster Sessions will take place on Feb. 4 from 10:00 am – 10:30 am and Feb. 5 from 4:30 pm to 5:00 pm in the Ballroom 20 Foyer. Henkel’s Dr. Mark Currie and Neil Poole will present the below:
- Compatibility Secures Reliability – Understand how solder flux compatibility (or lack thereof) with underfills, encapsulants, conformal coatings and other board-level materials can impact reliability.
- Solder Solutions for Harsh Environments – Conventional SAC alloys do not meet the stringent reliability standards for many systems that operate within harsh environments, such as automotive. Learn about a lead-free alloy designed to cope with tough conditions.
To discover more about these materials or any of Henkel’s ‘solutions across the board’, connect with a Henkel technology specialist in booth #3603 during IPC APEX EXPO or visit www.henkel-adhesives.com/electronics.
Share on:
Suggested Items
iNEMI Presents Packaging Interconnect Material Technology Series with Dr. Kazuhiro Nogita
09/09/2024 | iNEMIiNEMI, a leading electronics manufacturing industry association, is pleased to announce a two-part webinar series focusing on packaging interconnect material technology. Dr. Kazuhiro Nogita, a leading expert in the field, will present on September 17-24, 2024.
Indium Experts to Speak on Sustainable e-Mobility and PCB Supply Solutions at Productronica India
09/09/2024 | Indium CorporationIndium Corporation Senior Sales and Business Development Manager, Chris Nash, will present at the e-Mobility Conference at Productronica India, on September 12 in Delhi, India.
Eutect Overcomes Panel Soldering Challenges with New Gripper
09/06/2024 | Eutect GmbHThe selective soldering of assemblies in panels is not a real challenge. However, if you need to solder relatively large panels with towering components, specialists like those at Eutect GmbH have to step up to the plate.
AIM Solder Appoints Kevin Kwan as Business Development Manager in Asia
09/06/2024 | AIM SolderAIM Solder, a global leader in solder assembly materials for the electronics industry, is thrilled to announce the appointment of Kevin Kwan as Business Development Manager for the Asian market.
Solder Printing: A 1:1 Ratio of Technical and Creative
09/03/2024 | Nolan Johnson -- Column: Nolan's NotesWhen things get technical, I’m in my happy place. It’s why I work in technology in the first place. I also happen to enjoy creative pursuits, and my real happy place is when both happen at the same time. Over the years, it seems that most of us engaged in printed circuit design and manufacturing are similarly wired. I don’t think I’m alone in stating that finding a creative solution to a technical problem is one of the highlights of our workday. We get bonus points if the solution is particularly simple or uncomplicated.
Copyright © 2024 I-Connect007 | IPC Publishing Group Inc. All rights reserved.
Log in