-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueWet Process Control
In this issue, we examine wet processes and how to obtain a better degree of control that allows usable data to guide our decisions and produce consistently higher-quality products.
Don’t Just Survive, Thrive
If we are to be relevant and prosper during these next critical decades in electronics, we must do more than survive. As an industry, we can and must thrive. In this issue, our contributors explore these concepts meant to help you take your business to the next level.
Material Matters
Materials management is nuanced, multifaceted, and requires a holistic systems approach for business success. When building high mix, low volume, and high technology, managing materials and overall cost containment are even greater challenges.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - pcb007 Magazine
Book Excerpt: Thermal Management With Insulated Metal Substrates, Part 4
December 10, 2020 | Didier Mauve and Ian Mayoh, VentecEstimated reading time: 2 minutes
![](https://iconnect007.com/application/files/3916/3125/1611/Ventec_book.jpg)
The following is an excerpt from Chapter 4 of "The Printed Circuit Designer's Guide to... Thermal Management With Insulated Metal Substrates," written by Ventec International Group’s Didier Mauve and Ian Mayoh. In this free eBook, the authors provide PCB designers with the essential information required to understand the thermal, electrical, and mechanical characteristics of insulated metal substrate laminates.
Chapter 4: Application Examples
Main Application Areas
Insulated metal substrates find many applications in automotive and industrial LED, power conversion, general lighting, street safety, backlight unit, and e-vehicle sectors (Figure 4.1).
Figure 4.1: Primary applications for IMS.
Headlamps
Compact LED lamp units give car stylists extra freedom. Bright lighting at near-daylight color temperatures gives drivers a clear view. However, as much as 80% of the electrical power supplied is dissipated as heat, which presents engineers with severe thermal management challenges.
Matrix headlamps feature multiple closely-spaced emitters on a single substrate. A substrate of high thermal conductivity, featuring either an aluminum or copper baseplate, and dielectric thickness of about 0.002” (0.05 mm) is a typical choice to ensure long-term reliability. A non-reinforced dielectric minimizes stressors due to CTE mismatch between the copper foil and aluminum baseplate. A copper baseplate may be used if the matrix density is extremely high and the power is very high to address potential CTE mismatches. Spotlights with multiple boards, each containing two or three emitters, concentrate the thermal challenge on smaller substrates featuring an aluminum baseplate and 2–3 W/mK overall thermal conductivity including the dielectric layer, which is typically about 0.003–0.004” (0.075–0.010 mm).
Automotive Turn Signals
LEDs for turn signals are typically in the 3W power range. A three-emitter unit dissipates about 7 watts of thermal energy that must be extracted from the component. IMS is often the most efficient and cost-effective thermal connection to the metallic chassis. Extreme size and shape constraints can direct designers toward a substrate with 3 W/ mK thermal conductivity and 0.002” or 0.003” (0.05–0.075 mm) dielectric.
High-Power Motor Drive for Electric Power Steering
Electric power steering (EPS) and other motor-driven mechanisms, including high-power electric-traction inverters in EVs, can present even tougher thermal management challenges. Targets for module size and reliability can be met cost-effectively using a high-performing IMS with thermal conductivity of 3–4.2 W/mK and 0.004”–0.006” (0.10–0.15 mm) dielectric. Direct bonded copper (DBC) is an alternative. In extremely high-power applications, such as inverters, power transistors may be soldered to the IMS/DBC circuit layer as bare die, and a liquid-cooled heat sink attached to the baseplate. In some modules, such as combined onboard charger (OBC) and DC/DC-converter units for EVs, the baseplate is integrated with a cast metal chassis, and the specification determined in consultation with the foundry.
To download this free eBook, published by I-Connect007, click here.
To view the entire I-Connect007 eBook library, click here.
Suggested Items
Atotech to Participate at KPCA Show 2024
09/03/2024 | AtotechMKS’ Atotech will participate in this year’s KPCA Show 2024 in Incheon, held at Songdo Convensia from September 4-6, 2024.
Victory Announces Breakthrough in PCB Technology with New Product Launch
08/29/2024 | openPRShenzhen Victory Electronics Technology Co., Ltd., a leader in the printed circuit board (PCB) manufacturing industry, is proud to announce the successful development of a groundbreaking new product.
Connect the Dots: Designing for Reality—Electroless Copper
08/28/2024 | Matt Stevenson -- Column: Connect the DotsRoll up your sleeves because it's time to get messy. In a recent episode of I-Connect007’s On the Line with… podcast, we discussed electroless copper deposition. This process deposits a copper layer into the through-holes and vias of what will eventually be a PCB. Electroless copper deposition feels like a black box to many people. It sort of looks like a black box, too. The boards go in one side, come out the other, and emerge differently. So, let's crack open that black box and look inside.
Maximizing ROI Through Better Wet Process Control
08/20/2024 | I-Connect007 Editorial Team“When things get out of control, the variation in your wet process begins,” says Mike Carano,. “Just because they look like good boards and may even pass electrical test, it does not necessarily mean you have good boards. Once the chemistry is headed toward the right or left side of the process control parameter cliff, the plating is compromised. If the copper is thinner than it should be, when the customer puts it into service, the board may fail after 500 cycles vs. the requisite 1,000 or 2,000 cycles. The root cause issue is that you plated 7/10ths of a mil of copper instead of one-mil of copper because you were not controlling your process. The fact that you passed your own electric test becomes inconsequential.”
The Chemical Connection: Controlling an Alkaline Etch Bath With Low Copper Loading
08/07/2024 | Don Ball -- Column: The Chemical ConnectionThis month, I wanted to continue my discussion on how much process control is actually needed for high-density circuit production. However, in the last month, I have been called on to help with a specific process control problem: how to control an alkaline etch bath when you’re not etching much copper. This problem has been cropping up more frequently as smaller shops (and a few larger ones) concentrate on low-volume, high-value plated through-hole panels such as prototypes, resistor cores, etc.