NRL Develops Novel Monolayer Ferroelectric Hybrid Structures
January 6, 2017 | NRLEstimated reading time: 3 minutes
Scientists at the U.S. Naval Research Laboratory (NRL), Materials Science and Technology Division, have demonstrated that the intensity and spectral composition of the photoluminescence emitted from a single monolayer of tungsten disulphide (WS2) can be spatially controlled by the polarization domains in an adjacent film of the ferroelectric material lead zirconium titanate (PZT).
Domains consisting of electric polarization dipoles are written in a checkerboard pattern into a thin film of lead zirconium titanate (PZT) with a conductive atomic force microscope, and imaged with the same instrument (left panel). Both intensity and spectral distribution of the photoluminescence emitted from a monolayer of tungsten disulphide (WS2) transferred onto the PZT surface is strongly modulated by these polarization domains (right panel). (U.S. Naval Research Laboratory)
These domains are written in the PZT using a conductive atomic force microscope, and the photoluminescence (PL) is measured in air at room temperature. Because the polarization domain wall width in a ferroelectric can be as low as 1-10 nm, this approach enables spatial modulation of PL intensity and the corresponding carrier populations with potential for nanoscale resolution.
Single monolayer transition metal dichalcogenides (TMDs) such as WS2 exhibit striking optical properties due to their direct band gap. The dielectric screening is very low due to their two dimensional (2D) character, and thus their properties are strongly affected by their immediate environment, and can be modified and controlled by variations in local charge density due to adsorbates or electrostatic gating. This has generated keen interest in a wide variety of electronic and optical device applications.
The NRL scientist used a conducting atomic force microscope to write polarization domains into a PZT film in a checkerboard pattern. In each domain, the polarization dipole points either up out of the surface plane or down into the surface plane, and produces either positive or negative charge on the PZT surface, respectively. The team then transferred monolayer WS2 that they had grown by chemical vapor deposition techniques onto the PZT film.
They found that the PL intensity from the WS2 is high only from the areas over domains in the PZT where the polarization dipole points out of the surface plane, as shown in the adjacent figure. Further analysis revealed that the spectral composition of the PL was also strongly affected — the spectra from the “up” domains were dominated by neutral exciton contributions (a bound state of an electron and hole arising from Coulomb interaction), while those from the “down” domains were dominated by negatively charged exciton, or trion, contributions (an exciton with an extra electron).
“Fabricating these hybrid 2D/3D ferroelectric heterostructures enables one to purposefully design and modulate adjacent populations of trions and neutral excitons, creating lateral domains in any geometry of choice” notes Dr. Berend Jonker, senior scientist and principal investigator. Dr. Connie Li, lead author of the study, further points out: “Because the FE domains can be rewritten with an atomic force microscope and are non-volatile, this enables spatial modulation of the TMD properties with nanometer scale resolution.”
The payoff includes development of TMD materials and hybrid 2D/3D heterostructures with new functionality relevant to the DoD mission, including ultra-low power electronics, non-volatile optical memory and quantum computation for future DoD applications in information processing and sensing. The research results are reported in the December 4, 2016, issue of ACS Omega (DOI: 10.1021/acsomega.6b00302), the open access journal of the American Chemical Society. The paper was also selected as an ACS Editors’ Choice featured paper. The research team included Dr. Connie Li, Dr. Kathleen McCreary, and Dr. Berend Jonker from the Magnetoelectronic Materials & Devices Section in the Materials Science and Technology Division at NRL.
Suggested Items
Material Insight: The Dielectric Constant of PCB Materials
05/17/2024 | Dr. Preeya Kuray -- Column: Material InsightIn the world of PCB design, miniaturization can be achieved by using low dielectric constant (Dk) materials. Low Dk materials can allow for a reduction in thickness while maintaining a given trace width, leading to lower transmission loss and higher density circuitry.
IPC APEX EXPO: Some Thoughts About Growth
05/16/2024 | Dan Feinberg, I-Connect007After two and a half days of wandering the aisles at IPC APEX EXPO 2024, for the first time, I almost felt like I was exploring CES. There were so many booths and exhibits that I could describe, but I’d like to focus on the growth and huge value of this event, which has expanded well beyond just the growing and impressive exhibit show floor.
The Shaughnessy Report: Unlock Your High-speed Material Constraints
05/15/2024 | Andy Shaughnessy -- Column: The Shaughnessy ReportThe world of PCB materials used to be a fairly simple one. It was divided into two groups: the “traditional” laminates, often called FR-4, and the high-speed laminates developed especially for high-speed PCBs. These were two worlds that usually didn’t collide. But then traditional laminates started getting better, and high-speed designers and design engineers took notice and started to reconsider what FR-4 could be used for.
Breaking High-speed Material Constraints: Design007 Magazine — May 2024
05/14/2024 | I-Connect007 Editorial TeamDo you need specialty materials for your high-speed designs? Maybe not. Improvements in resins mean designers of high-speed boards can sometimes use traditional laminate systems instead of high-speed materials, saving time and money while streamlining the fab process. In the May 2024 issue of Design007 Magazine, our contributors explain how to avoid overconstraining your materials when working with high-speed boards.
Indium Experts to Present at Electronics in Harsh Environments SMTA Conference
05/13/2024 | Indium Corporationndium Corporation Technical Manager for Europe, Africa, and the Middle East, Karthik Vijay, will deliver a technical presentation and Indium Corporation Senior Technologist, Dr. Ronald Lasky, will deliver both a workshop and technical presentation at the Electronics in Harsh Environments SMTA Conference on May 14-16 in Copenhagen, Denmark.