Dense Yet Transparent Materials Offer New Way to Control Light
July 18, 2016 | OSAEstimated reading time: 3 minutes
Researchers recently made the surprising discovery that a special class of materials called “hyperuniform materials” can be both dense and transparent. This work demonstrates a new way to control light and could lead to novel materials for many light-based applications including solar photovoltaics. Hyperuniform materials can be made of plastic or glass that contains light-scattering particles spaced in a disordered, but not completely random, pattern.
In The Optical Society's journal for high impact research, Optica, researchers led by Rémi Carminati, Institut Langevin, ESPCI Paris and CNRS, France, detail the transparency properties they discovered using computer simulations and outline a theory to explain the wavelengths of light for which hyperuniform materials appear transparent.
“We showed that hyperuniform materials can be transparent for certain wavelengths while at the same time being very dense,” said Carminati. “Our work is very fundamental and we have found something very new.”
Optical properties of hyperuniform materials
Although hyperuniform materials have been studied for the last decade, their optical properties are only recently being uncovered. Researchers previously showed that a hyperuniform material is transparent when it has a particle density that allows light going through the material to interact with each particle no more than once.
“Typically if you make a material denser, it will scatter light more and thus appear opaque,” said Carminati. “However, what we've shown is that if you make the hyperuniform material denser to the point where light will interact with many particles on its way through the material, you can still observe transparency. This is really unexpected, and nobody has examined it before.”
This surprising characteristic of dense hyperuniform materials occurs because of the microscopic-scale ordering of the particles in the material. Although the uniformly spaced particles scatter light in all directions, most of the light waves interfere with each other, stopping all the scattered light except for light traveling in the forward direction through the material. This means that the light entering the material continues in the forward direction as if it was going through a homogeneous material, making the material appear transparent. The wavelengths of light for which the material is transparent depend on the exact characteristics of the material used.
The dense hyperuniform materials are highly ordered at a scale of about 1 micron, but remain disordered at a larger scale. This property makes the materials less prone to fabrication errors, which means they could be made in large pieces. Commercial techniques such as lithography could be used to make a hyperuniform material like the one simulated in this study, but Carminati says that developing a fabrication technique that produces hyperuniformity in a natural way could allow manufacturing of such materials in large quantities.
Controlling light waves
“When light waves interact with a material, the scattering that typically occurs destroys many interesting properties of the waves,” said Carminati. “Our work shows that it is possible to use the material itself to control the way the waves propagate. This is a big paradigm change. Producing specific materials that are transparent for a spectral region for which you don't expect the material to be transparent is just one example of what can be done.”
Carminati points out that while applications for these dense, transparent materials are a long way off, the new study shows the potential for making materials that offer a variety of optical properties. For example, a material could be made to change from randomly spaced particles to perfectly spaced particles in response to an external electric field, thus switching from appearing white to being transparent.
Hyperuniform materials might also be useful for photovoltaics because they offer a way to manipulate how diffuse light enters a material and is absorbed by the particles. Tuning the material so that it is very absorbent across a wide variety of wavelengths could be used to convert light into energy.
Since light waves behave much like acoustic and quantum waves, materials that are dense and transparent could, in principle, be designed for other types of waves. “What we have demonstrated is not specific to optics,” said Carminati. “It likely applies to wave physics in general and could open up new applications in other fields.”
Suggested Items
Material Insight: The Dielectric Constant of PCB Materials
05/17/2024 | Dr. Preeya Kuray -- Column: Material InsightIn the world of PCB design, miniaturization can be achieved by using low dielectric constant (Dk) materials. Low Dk materials can allow for a reduction in thickness while maintaining a given trace width, leading to lower transmission loss and higher density circuitry.
IPC APEX EXPO: Some Thoughts About Growth
05/16/2024 | Dan Feinberg, I-Connect007After two and a half days of wandering the aisles at IPC APEX EXPO 2024, for the first time, I almost felt like I was exploring CES. There were so many booths and exhibits that I could describe, but I’d like to focus on the growth and huge value of this event, which has expanded well beyond just the growing and impressive exhibit show floor.
The Shaughnessy Report: Unlock Your High-speed Material Constraints
05/15/2024 | Andy Shaughnessy -- Column: The Shaughnessy ReportThe world of PCB materials used to be a fairly simple one. It was divided into two groups: the “traditional” laminates, often called FR-4, and the high-speed laminates developed especially for high-speed PCBs. These were two worlds that usually didn’t collide. But then traditional laminates started getting better, and high-speed designers and design engineers took notice and started to reconsider what FR-4 could be used for.
Breaking High-speed Material Constraints: Design007 Magazine — May 2024
05/14/2024 | I-Connect007 Editorial TeamDo you need specialty materials for your high-speed designs? Maybe not. Improvements in resins mean designers of high-speed boards can sometimes use traditional laminate systems instead of high-speed materials, saving time and money while streamlining the fab process. In the May 2024 issue of Design007 Magazine, our contributors explain how to avoid overconstraining your materials when working with high-speed boards.
Indium Experts to Present at Electronics in Harsh Environments SMTA Conference
05/13/2024 | Indium Corporationndium Corporation Technical Manager for Europe, Africa, and the Middle East, Karthik Vijay, will deliver a technical presentation and Indium Corporation Senior Technologist, Dr. Ronald Lasky, will deliver both a workshop and technical presentation at the Electronics in Harsh Environments SMTA Conference on May 14-16 in Copenhagen, Denmark.