Study: Raising Temperature Changes an Element's Electronic "Topology"
November 1, 2016 | CaltechEstimated reading time: 2 minutes
Materials scientists at Caltech have discovered a new way that heat tweaks the physical properties of a material.
Experimenting with an alloy of iron and titanium (FeTi), a team led by Caltech's Brent Fultz found that increasing heat alters the topology of the material's Fermi surface—an abstract map of the allowable energy states that can be occupied by electrons.
Fultz, the Barbara and Stanley R. Rawn, Jr., Professor of Materials Science and Applied Physics in the Division of Engineering and Applied Science, likens a Fermi surface to a planet covered by a smooth ocean and rocky landmasses. The ocean is made up of electrons, while the land represents voids where electrons are not present. Placing an element under extreme pressure—like that in Earth's core—can cause landforms lurking just below the surface to emerge, in turn altering where electrons are likely to be found. The appearance of these new features in a Fermi surface is called an electronic topological transition (ETT). The concept of an ETT was proposed by the Russian physicist I. M. Lifshitz in 1960, and ETTs have been observed by subjecting metals to pressures on the order of 100,000 atmospheres.
Heating causes electrons to slosh around within the Fermi surface, but, as with waves moving on water, the coastlines—the boundaries between electrons and electron-less voids—remain about the same. However, Fultz and his colleagues noticed that because heat also displaces atoms, heating can in some cases reveal landforms hidden below the surface of that metaphorical Fermi sea.
In practical terms, altering the topology of the Fermi surface alters the chemical properties of a metal or alloy, which in turn alters its electrical conductivity.
The potential value to engineers lies in the fact that it is much easier to raise the temperature of a material than it is to place it under the sort of pressure needed to force an ETT. "The pressures needed to cause an ETT are intense, while the temperature changes needed are comparatively low," says Fultz. Indeed, gigapascals of pressure are required to cause an ETT—that is, tens of thousands of times the pressure of Earth's atmosphere. However, Fultz and his colleagues noted ETTs occurring within hundreds of degrees Fahrenheit of temperature change.
The discovery was something of an accident—the result of computationally chasing down anomalous results while performing neutron scattering tests on an FeTi alloy that is of interest to engineers because it is remarkably strong and stretchable.
Neutron scattering reveals details about a material's atomic structure. In the method, a beam of neutrons is fired at a material and the energies and angles of the scattered neutrons are recorded and analyzed. In particular, Fultz's group was using neutron scattering to study the vibrations of atoms in crystals, which almost always move and buzz slightly. The researchers found that, with increasing temperatures, the specific patterns of buzzing changed dramatically in a way that could not be explained through known mechanisms.
Caltech graduate student Fred Yang (MS '15), lead author of a paper about the discovery appearing in the journal Physical Review Letters, ran numerous computer simulations that suggested the temperature-related change could be explained by an ETT in FeTi.
Next, Fultz and Yang plan to explore other elements with features lurking just below their Fermi surfaces.
Suggested Items
Ansys’ Collaboration with Schrödinger will Accelerate Materials Development with Unprecedented Multiscale Simulation
05/09/2024 | ANSYSAnsys and Schrödinger are collaborating to deliver an ICME approach that bridges the gap between materials discovery and product development.
2024 Apple iPad Pro Estimated to Ship Between 4.5 to 5 Million Units
05/08/2024 | TrendForceApple’s recent product launch in May introduced a lineup of new tablets featuring advanced AMOLED screens. Notably, the Pro version boasts a dual-layer tandem structure designed to address the longstanding challenges of screen burn-in and lifespan that are common with AMOLED displays.
AIM Solder Signs Shinil Fl Ltd. as New Distributor for Korea
05/08/2024 | AIM SolderAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce a new distribution partnership with Shinil Fl Ltd., a prominent supplier of technological solutions in the SMT and semiconductor sectors.
IDTechEx Discusses Low-Loss Materials: The Enabler of Future Connected Vehicles?
05/06/2024 | IDTechExFuture connected vehicles will offer future drivers a safer, smoother, and more convenient driving experience. Not only will drivers get access to more navigation and entertainment options, but they will also gain access to safety technologies that will potentially reduce accidents, improve congestion, and reduce emissions globally by allowing vehicle safety systems to communicate with each other and with city traffic infrastructure.
LQDX Divests Aluminum Soldering Business - Mina™ - to Taiyo America Inc.
05/02/2024 | PRNewswireLQDX, formerly known as Averatek Corp., developer of high-performance materials for advanced semiconductor manufacturing, today announced that it has divested its aluminum soldering business – known as MinaTM – to Taiyo America Inc., a global market leader in advanced electronic materials.