Target Condition: Are Autorouters Friend or Foe?
Fresh PCB Concepts: Assembly Challenges with Micro Components and Standard Solder Mask Practices
Elementary Mr. Watson: Retro Routers vs. Modern Boards—The Silent Struggle on Your Screen
Paving the Way for 400Gb Ethernet and 5G
June 26, 2018 | Chang Fei Yee, Keysight TechnologiesEstimated reading time: 1 minute
This article briefly introduces the 4-level pulse amplitude modulation (PAM-4) and its application in 400 Gigabit Ethernet (400GbE), to support the booming data traffic volume in conjunction with the deployment of 5G mobile communications. Furthermore, this article also highlights the essential pre-layout effort from signal integrity perspective for physical (PHY) link design on a PCB, including material selection, transmission line design and channel simulation to support 56Gbps data rate that paves the way for seamless communication in 400GbE.
I. Introduction
400GbE is a new wired communication standard to accommodate the booming data traffic volume with the implementation of 5G mobile communications. In the implementation of 400GbE communication, electrical interface with 4-level pulse amplitude modulation (PAM-4) signaling over 8 lanes is adopted. The communication of eight lanes at 56Gbps (i.e., 28GBaud) per lane enables the total bandwidth of 400Gbps over the Ethernet. The electrical specifications of 400GbE with PAM-4 signaling are defined in IEEE 802.3bs.
PAM-4 has 4 digital amplitude levels, as shown in Figure 1. It has an advantage over non-return-to-zero (NRZ) signals because each level or symbol in PAM-4 contains two information bits providing twice as much data throughput for the same baud rate. For instance, 28GBaud is equivalent to 56Gbps in PAM-4 and 28Gbps in NRZ respectively.
II. Essential pre-layout effort from signal integrity perspective
According to guidelines, a PAM-4 channel with trace length up to 8 inches on a PCB shall have insertion loss less than 10dB at 14GHz (i.e., Nyquist frequency of 28GBaud) and 20dB at 28GHz (i.e., 2nd harmonic of 28GBaud) respectively to achieve seamless data communication between the transceivers.
To read this entire article, which appeared in the May 2018 issue of Design007 Magazine, click here.
Share on:
Suggested Items
Facing the Future: Time for Real Talk, Early and Often, Between Design and Fabrication
07/08/2025 | Prashant Patel -- Column: Facing the FutureThere has always been a subtle but significant divide between those who design and those who build printed circuit boards. It’s not a hostile gap, but it is a real one, and in today’s high-speed, high-complexity, high-stakes environment, that gap is costing us more than time and yield. It’s costing us innovation.
DownStream Acquisition Fits Siemens’ ‘Left-Shift’ Model
06/26/2025 | Andy Shaughnessy, I-Connect007I recently spoke to DownStream Technologies founder Joe Clark about the company’s acquisition by Siemens. We were later joined by A.J. Incorvaia, Siemens’ senior VP of electronic board systems. Joe discussed how he, Rick Almeida, and Ken Tepper launched the company in the months after 9/11 and how the acquisition came about. A.J. provides some background on the acquisition and explains why the companies’ tools are complementary.
Elementary Mr. Watson: Retro Routers vs. Modern Boards—The Silent Struggle on Your Screen
06/26/2025 | John Watson -- Column: Elementary, Mr. WatsonThere's a story about a young woman preparing a holiday ham. Before putting it in the pan, she cuts off the ends. When asked why, she shrugs and says, "That's how my mom always did it." She asks her mother, who gives the same answer. Eventually, the question reaches Grandma, who laughs and says, "Oh, I only cut the ends off because my pan was too small." This story is a powerful analogy for how many PCB designers approach routing today.
Connect the Dots: The Future of PCB Design and Manufacturing
07/02/2025 | Matt Stevenson -- Column: Connect the DotsFor some time, I have been discussing the increasing complexity of PCBs and how designers can address the constantly evolving design requirements associated with them. My book, "The Printed Circuit Designer’s Guide to… Designing for Reality," details best practices for creating manufacturable boards in a modern production environment.
Siemens Turbocharges Semiconductor and PCB Design Portfolio with Generative and Agentic AI
06/24/2025 | SiemensAt the 2025 Design Automation Conference, Siemens Digital Industries Software today unveiled its AI-enhanced toolset for the EDA design flow.