Global Citizenship: Together for a Perfect PCB Solution
Smart Automation: Odd-form Assembly—Dedicated Insertion Equipment Matters
Nolan’s Notes: Everyone Has Their Eye on India
LA/Orange County SMTA Expo and Tech Forum Review
December 9, 2019 | Dan Feinberg, Technology Editor, I-Connect007Estimated reading time: 2 minutes
A few weeks ago, I was invited to attend the LA/Orange County SMTA Expo and Tech Forum, which was held in Long Beach, California (Figure 1). Earlier this year, I started covering the quarterly lunch and learn sessions presented by the Orange County Chapter of the IPC Designers Council. Circuit design is not a topic I have been involved with for many decades, but I find that the lectures, presentations, and updates are highly informative, and the discussions with the other attendees are well worth the time spent.
Figure 1: SMTA show floor.
This specific event combined an exhibit of about 50 companies put on by the local SMTA chapter with a series of valuable presentations and Q&A sessions presented by the IPC Designers Council. The show floor was moderately busy with a constant flow of attendees walking through (Figures 2 and 3). There was a good mixture of equipment and consumable suppliers, all very willing to discuss their products as well as general industry happenings.
Figure 2: Indium and Nikon booths.
Figure 3: PFC Flexible Circuits table.
There were two excellent presentations, one of them entitled “Why Are We Cleaning No-Clean?” by Mike Konrad from Aqueous Technologies, which was divided into two sessions (Figure 4). The content was interesting, and Mike’s presentation was informative and entertaining. It seems that many assemblers have implemented a cleaning protocol for assemblies reflowed with no-clean flux, as many have experienced residue-related failures. Mike also spoke about the factors that affect residue tolerance and methods to predict an assembly’s residue tolerance.
The other presentation was by Keith Bryant, an advanced design engineering consultant who spoke on X-ray inspection advances for BGAs and bottom-terminated components, including the problem of voids within the layers of electronics or in the PCB itself. Voiding is a problem because it can affect both the short- and long-term joint strength and reliability as well as the thermal conductivity, thus reducing the heat that would otherwise be dissipated away from key areas. While X-Ray inspection has long been used to nondestructively probe for these and other issues, there have been recent developments improving in 2D and 3D X-ray inspection.
The combination of a modest exposition showing many new offerings and the ability to discuss them with those that represent them, along with an opportunity to mingle with others in the industry and attend valuable and interesting presentations locally, provided great value for anyone within an hour’s drive. Based on the attendance, it seems that this has been recognized.
Share on:
Testimonial
"In a year when every marketing dollar mattered, I chose to keep I-Connect007 in our 2025 plan. Their commitment to high-quality, insightful content aligns with Koh Young’s values and helps readers navigate a changing industry. "
Brent Fischthal - Koh YoungSuggested Items
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
09/12/2025 | Marcy LaRont, I-Connect007We may be post-Labor Day, but it is still hot-hot-hot here in the great state of Arizona—much like our news cycles, which have continued to snap, crackle, and pop with eye-raising headlines over this past week. In broader global tech news this week, AI and tariff-type restrictions continues to dominate with NVIDIA raising its voice against U.S. lawmakers pushing chip restrictions, ASML investing in a Dutch AI start-up company to the tune of $1.5 billion, and the UAE joining the ranks of the U.S. and China in embracing “open source” with their technology in hopes of accelerating their AI position.
IPS, SEL Raise the Bar for ENIG Automation in North America
09/11/2025 | Mike Brask, IPSIPS has installed a state-of-the-art automated ENIG plating line at Schweitzer Engineering Laboratories’ PCB facility in Moscow, Idaho. The 81-foot, fully enclosed line sets a new standard for automation, safety, and efficiency in North American PCB manufacturing and represents one of the largest fully enclosed final finish lines in operation.
Dan Feinberg on Walt Custer: Remembering an Extraordinary Business Associate and Friend
09/09/2025 | Dan Feinberg, Technology Editor, I-Connect007The passing of Walt Custer marks the end of an era for all those who knew him and were helped and impressed by his presence, both personally and professionally. Walt's life was characterized by his unwavering commitment to the industry, his profound wisdom and willingness to share it, and his infectious enthusiasm for everything he did.
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
09/05/2025 | Andy Shaughnessy, I-Connect007It’s almost fall here in Atlanta, and that means that the temperature is finally dropping. And it quit raining! It’s been raining since March, and I’m so over it, as the social influencers say. Last night we grilled out on the deck, and it wasn’t hot, and we didn’t get rained on. Life is good. It was a busy week in the industry. In this installment of my must-reads, we say goodbye to Walt Custer, the man who made PCB data points interesting for the rest of us.
UHDI Fundamentals: UHDI Technology and Industry 4.0
09/03/2025 | Anaya Vardya, American Standard CircuitsUltra high density interconnect (UHDI) technology is rapidly transforming how smart systems are designed and deployed in the context of Industry 4.0. With its capacity to support highly miniaturized, high-performance, and densely packed electronics, UHDI is a critical enabler of the smart, connected, and automated industrial future. Here, I’ll explore the synergy between UHDI and Industry 4.0 technologies, highlighting applications, benefits, and future directions.