-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueBreaking High-speed Material Constraints
Do you need specialty materials for your high-speed designs? Maybe not. Improvements in resins mean designers of high-speed boards can sometimes use traditional laminate systems. Learn more in this issue.
Level Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Book Excerpt: The Electronics Industry’s Guide to… The Evolving PCB NPI Process, Chapter 1
September 28, 2022 | I-Connect007 Editorial TeamEstimated reading time: 2 minutes
Chapter 1
How the NPI Process Has Changed and Where We're Going
When forging into unknown territory or exploring new ground, it can help to look at where we’ve been so we can orient ourselves.
Just a few decades ago, electronics manufacturing companies were producing high volumes of few products. The efficiency of electronics manufacturing lines is measured by overall equipment effectiveness (OEE) and total effective equipment performance (TEEP). Back then, this meant optimizing the time it took to build a single board. If the time it took to build one board could be reduced by a few seconds, the savings would be multiplied by the number of boards being built. This could be in the hundreds of thousands or millions of boards, with no changes in the line configuration. If it took a day to change over from one product to another, it didn’t matter because the TEEP/OEE was driven by the time it took to build a board.
For example, consider that it takes 35 seconds to place components on a single board, and I need to make 250 boards. My handling time (the time it takes to load a board into the machine and get it out after) is 10 seconds, then the total time to build the 250 boards will be (35 + 10) • 250 = 11,250 seconds. This equates to about 188 minutes, or approximately three hours. If it takes four hours to changeover—namely reconfigure the line before starting a different PCB—to a new product, my OEE will be less than 50%, considering no other external factors. As the batch size goes down, the changeover time dominates the OEE figure.
In today’s high-mix, low-volume production environments, performance is further enhanced with line efficiency. Line efficiency is the ratio of the number of hours during which a high-volume, pick-and-place machine places parts on the PCB, divided by the number of hours during which the SMT assembly lines are staffed (placement time/staffed time x 100). It is a solid number, simple to obtain, and has great value as a key performance indicator.
With higher product mixes, the number of NPIs being processed increases. Changeovers on the shop-floor line can happen daily or many times a day. This also means the time it takes to process the source design data has increased. This data-processing time is becoming a more important consideration compared to when NPI processing was not a daily task in the lower mix environment. As product mix has gone up, there has been a move from mixed vendor lines focused on ultimate through-put to single vendor lines focused on flexibility and shorter changeovers. There may be more than one pick-and-place vendor brand in the factory, but each line commonly has only one brand now.
Download your free copy today! You can also view other titles in our full library.
We hope you enjoy The Electronics Industry’s Guide to… The Evolving PCB NPI Process.
Suggested Items
Murata Obtains ISO 26262 Certification for Functional Safety in Automotive Applications
05/21/2024 | MurataMurata Manufacturing Co., Ltd., obtained the ISO 26262 development process certification for Functional Safety* Automotive ISO 26262 from the German third-party certifier SGS-TÜV Saar GmbH on February 13, 2024.
Quantic Electronics Announces Acquisition of M Wave Design
05/20/2024 | Quantic ElectronicsQuantic® Electronics, a portfolio company of Arcline Investment Management, announced the acquisition of M Wave Design, a leading supplier of ferrite-based RF and Microwave components for aerospace, defense, and quantum computing applications.
Spring 2024 Santa Clara County Flexfactor Finals Held at Nextflex
05/20/2024 | NextFlexNextFlex hosts this semester’s FlexFactor. Four teams of high school students competed by pitching their inventive products to a panel of esteemed judges composed of Robert de Neve, General Partner & Chief Strategist General Partner & Chief Strategist at NextPhase Ventures; Christine Holly Ngo, VP of Operations and Business Development at Silicon Valley Elite Manufacturing, Inc; and Jackson Rambough, FHE Design and Process Engineer at NextFlex.
HBM3e Production Surge Expected to Make Up 35% of Advanced Process Wafer Input by End of 2024
05/20/2024 | TrendForceTrendForce reports that the three largest DRAM suppliers are increasing wafer input for advanced processes. Following a rise in memory contract prices, companies have boosted their capital investments, with capacity expansion focusing on the second half of this year.
Taiflex Announces Grand Opening of Thailand Factory
05/17/2024 | TAIFLEX Scientific Co. LtdTaiflex Scientific Co., Ltd., a global leader in advanced flexible printed circuit (FPC) materials, held the grand opening ceremony of its Thailand factory at the Amata City Chonburi Industrial Estate in Chonburi, Thailand.