-
-
News
News Highlights
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueThe Hole Truth: Via Integrity in an HDI World
From the drilled hole to registration across multiple sequential lamination cycles, to the quality of your copper plating, via reliability in an HDI world is becoming an ever-greater challenge. This month we look at “The Hole Truth,” from creating the “perfect” via to how you can assure via quality and reliability, the first time, every time.
In Pursuit of Perfection: Defect Reduction
For bare PCB board fabrication, defect reduction is a critical aspect of a company's bottom line profitability. In this issue, we examine how imaging, etching, and plating processes can provide information and insight into reducing defects and increasing yields.
Voices of the Industry
We take the pulse of the PCB industry by sharing insights from leading fabricators and suppliers in this month's issue. We've gathered their thoughts on the new U.S. administration, spending, the war in Ukraine, and their most pressing needs. It’s an eye-opening and enlightening look behind the curtain.
- Articles
- Columns
- Links
- Media kit
||| MENU - pcb007 Magazine
Shrinking Silicon, EMI, and SI
March 3, 2023 | Andy Shaughnessy, Design007 MagazineEstimated reading time: 2 minutes

As IC features continue to shrink, the PCB designer’s job gets more interesting—signal speeds and rise times are increasing, they’re encountering EMI and signal integrity issues once only seen in the RF world.
Dr. Todd Hubing is a longtime EMC instructor, president of LearnEMC, and a professor emeritus of the Electrical and Computer Engineering program at Clemson University. I asked Todd to discuss the challenges that shrinking silicon can present for traditional PCB designers, as well as the opportunities and benefits of smaller chip features.
Andy Shaughnessy: Shrinking silicon is causing an increase in EMI and SI issues for PCB designers and EEs. What sort of problems does shrinking silicon cause?
Todd Hubing: When the features of an IC shrink, transition times tend to be faster, and the high-frequency content of digital signals tends to increase. When newer, faster ICs are used in products that were designed with the older versions of those ICs, those products can suddenly start failing to meet EMC or SI requirements even though there was no nominal change in the design. ICs with smaller features can also be more susceptible to damage by voltage transients, though that largely depends on the mitigation features built into the design.
Shaughnessy: What is the relationship between smaller silicon and EM fields, and what can these designers do to proactively fight EMI and SI?
Hubing: Field coupling directly from an IC is not directly affected by smaller silicon. Field coupling depends more on the currents pulled through the inductance of the lead-frame. Shrinking the features on the silicon can cause those currents to be higher or lower at any given frequency depending on the application.
To protect against future silicon feature-size changes, PCB designers should always proactively control the transition times of any signal that could ultimately be the source of crosstalk or radiated emissions. They shouldn’t rely on “slow” devices to meet EMI and SI requirements.
Shaughnessy: If we add increased rise time and faster signals into this mix, how does material and material selection figure into the equation? Do you think OEMs should select their material, or allow the fab to do so?
Hubing: I believe laminate selection is strictly an SI issue, and then only for the fastest digital signals. Choosing whether to let the fabricator select the laminate depends on the many factors, but, in my opinion, that decision is unlikely to be impacted by silicon shrinkage.
To read this entire interview, which appeared in the February 2023 issue of Design007 Magazine, click here.
Suggested Items
Insulectro & Dupont Host Technology Symposium at Silicon Valley Technology Center June 25
06/22/2025 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, and DuPont, a major manufacturer of flex laminates and chemistry, invite fabricators, OEMS, designers, and engineers to attend an Innovation Symposium – Unlock the Power - this Wednesday, June 25, at DuPont’s Silicon Valley Technology Center in Sunnyvale, CA.
Ventec Strengthens Commitment to Halogen-Free PCB Manufacturing in Europe
06/11/2025 | Ventec International GroupVentec International Group, the PCB materials innovator, manufacturer, supplier and one-stop shop for copper clad laminates, prepregs, as well as process consumables and PCB manufacturing equipment has established volume inventory of halogen-free FR4.1 and FR15.1 PCB materials at its European hub in Germany.
Ventec International Group Enters into a Fulfillment and Supply Agreement with Matrix and Launches Ventec Americas
06/09/2025 | Ventec International GroupVentec is excited to announce a new partnership with Matrix aimed at enhancing the fulfillment, value-added conversion, and distribution of PCB base materials across the North American market. This collaboration is set to significantly improve supply chain efficiency, and delivery performance for the company's North American customers.
Panasonic Appoints Matrix as its Authorized Distributor in Europe
06/03/2025 | Matrix ElectronicsEffective July 1st, 2025, Panasonic Industry Co., Ltd. has appointed Matrix Electronics Limited as its Authorized Distributor in the European region.
From DuPont to Qnity: A Bold Move in Electronics Materials
05/14/2025 | Marcy LaRont, I-Connect007DuPont has announced the intended spinoff of a public independent electronics company, Qnity, which will serve as a solutions provider to the semiconductor and electronics industries to enhance competitiveness and innovation in advanced computing, smart technologies, and connectivity. In this interview, Jon Kemp, Qnity CEO-elect and current president of DuPont’s Electronics business, shares his insights on the strategic separation from DuPont.