Book Excerpt: 'The Printed Circuit Designer's Guide to... Manufacturing Driven Design,' Chapter 2
August 23, 2023 | I-Connect007 Editorial TeamEstimated reading time: 2 minutes
Excerpt from: The Printed Circuit Designer's Guide to... Manufacturing Driven Design, Chapter 2: Why a Change is Needed
Contemporary Complexity
In a recent survey on the increasing complexity of electronics design, it was reported that 68% of companies were facing increasing pressure to miniaturize their electronics form factors. This report mirrors global trends seen within the industry. It represents an increased burden placed upon the printed circuit board designer to put more functionality into a smaller space, and on the manufacturer to produce with a smaller margin of error.
This report highlights the interconnectedness of these complexity trends. The study also showed 68% of respondents are facing increasing pressure to bring the cost of their electronic products down, with 75% acknowledging the increasing challenge these factors brought to the manufacturing process. In line with quality initiatives, 74% identified the pressure on reliability of the products to also be increasing.
One of the questions I ask virtually every designer is, “How often do you get Technical Queries (TQs) from your suppliers related to a design you sent them?” I find the answer is almost always between 50% and 100% of the time. The good news is that most fabrication and contract manufacturing partners likely have a DFM software solution in place to validate designs before they are committed to manufacturing.The downside is your organization is dependent upon them to look out for your interests, and this typically adds a one- to two-week delay from submission before you even begin receiving TQs from them.
Such communication is often iterative and reported to be the single largest bottleneck encounter between design and manufacturing. There are times when the fabricators find it necessary to make radical changes, which requires extensive communication, adding yet another dimension to the TQ recipient. If it is the subject matter expert for the design, then the TQ is frequently mitigated for that design, meaning that same occurrence will likely occur yet again on other designs. Manufacturing experts need to be involved in addressing the occurrence of the TQ to reduce the likelihood of the reoccurrence.
Your supplier is naturally limited in their ability to perform this DFM. They don’t know what a board does and have no context for the design decisions that went into creating that function. Manufacturers naturally lack the design intent driven by your organization and, as such, may not be able to catch every issue within a design. As a general rule, manufacturers build to print. They are responsible for realizing the design given, not ensuring that the design works as intended.
Suggested Items
Marcy’s Musings: The ‘Magic’ of Additive Processes
05/21/2024 | Marcy LaRont -- Column: Marcy's MusingsThough modern semi-additive and fully additive technologies are still emerging for PCB manufacturing, additive technology itself is not new. Many PCB fabricators find themselves at a crossroads when deciding whether to change their current processes and go additive or stay the course until something significant compels a change. But change is on the horizon, and it seems to be driven by significant technological advancements in chips and advanced packaging, offering PCB fabricators some additive manufacturing solutions to explore.
Real Time with… IPC APEX EXPO 2024: Custom PCB Solutions With Adura
05/20/2024 | Real Time with...IPC APEX EXPOColumnist Dan Beaulieu and Sumit Tomar, CEO of Adura, discuss the company's comprehensive manufacturing of custom PCBs. The company excels in thermal PCB technology for enhanced conductivity. As Sumit explains, they also plan to venture into power management, leveraging their U.S.-based manufacturing capabilities.
Zentech First to Adopt IPC Apprenticeship National Program Standards
05/20/2024 | Cory Blaylock, IPCIPC achieved a landmark in 2023 by creating an apprenticeship program approved by the U.S. Department of Labor. With such a registered framework in place, industry can work through IPC to secure local, state, and federal dollars for workforce development in a way they’ve never been able to do before. Zentech Manufacturing, headquartered in Baltimore, Maryland, with production facilities in Bloomington, Illinois, and Richardson, Texas, is the first employer partner to adopt IPC’s national program. Click here to read their story.
Danutek Celebrates 20 Anniversary
05/20/2024 | DanutekDanutek, a leading supplier of capital equipment and service support to the electronics manufacturing sector in Europe, proudly marks its 20th anniversary this year.
GlobalFoundries Appoints KC Ang as President of Asia
05/20/2024 | GlobalFoundriesGlobalFoundries (GF) announced the appointment of industry and company veteran, Kay Chai (KC) Ang, as President of Asia and Chairman of China.